Brother HL-1060 Series manual Removing the Drum Unit

Page 53

CHAPTER 5 MAINTENANCE

Follow these steps to replace the drum unit:

1.Turn off the power switch.

2.Open the top cover and remove the old drum unit.

Fig. 5-10 Removing the Drum Unit

Warning

After you have just used the printer, some internal parts of the printer are extremely hot. When you open the top cover of the printer, never touch the shaded parts shown in the following illustration.

High Temperature

Fig. 5-11 Inside the Printer

3.Remove the toner cartridge from the drum unit and keep it in a safe place. For more information, see “REPLACIN G THE TONER CARTRIDGE” in this chapter.

✒Note

∙Discard the used drum unit according to local regulations. If you are not sure of them, consult your local dealer/retailer. Be sure to seal the drum unit tightly so that toner powder does not spill out of the unit. Do not discard used drum units with domestic rubbish.

∙It is recommended to put the drum unit on a piece of disposable paper or cloth in case of accidental toner spill or scatter.

CHAPTER 5 –7

Image 53

Contents Brother Laser Printer Please read this manual thoroughly before using the printerShipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice TrademarksTo Use the Printer Safely Definitions of Warnings, Cautions, and NotesTable of Contents Index International Energy Star Compliance Statement RegulationsIndustry Canada Compliance Statement For Canada Only FDA Regulations For 110-120 V Model Only Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model OnlyGeräuschemission / Acoustic Noise Emission For Germany Only Important For Your SafetyImportant Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the PrinterPrinter Overview About Your PrinterFeatures Enhanced Memory Management Remote Printer Console Program for DOSPopular Printer Emulation Support Low Running Cost Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Environment Power SupplyOperating and Storage Environment Introduction Paper Type Paper Size Paper SpecificationsUSER’S Guide Fan the Paper Straighten the Paper RemarksEnvelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the FeederMoving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing Manual Feed Slot When you load one sheet of paper manuallyWhen you load more than one sheet of paper manually Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support WireReady Paper Lamp Lamps and SwitchFeeder Lamp Data Toner LampDrum Lamp Switch Alarm LampOther Control Features Sleep ModeLamp Lit Choice Function Test Print ModeProtection Control Features Set by the Brother DriverAPT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100MSelecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface ParametersBit BitsDTR only OffNone Connecting the Serial Interface CableOptions BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional MemoryUnplug the power cord Disconnect the interface cable Installing the SimmRemove the main controller board Replacing the Toner Cartridge Chapter MaintenanceRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum UnitGently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed RollersRE-PACKING the Printer 26 Removing the Drum Unit Assembly27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a GlanceSimm Error ActionTroubleshooting NV-RAM Service CallsLocating Paper Jam Position Paper JamsPaper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer HardwareQuestion Setting Up the Printer for WindowsSetting Up the Printer for DOS When Using the Optional BR-Script 2 ROM Board BR-3000 Setting Up the Printer for Apple Macintosh ComputersWhen Using the Optional RS-100M Serial Interface Paper Handling Printing Together right now, over Print QualityToner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer SpecificationsFunctions Electrical and Mechanical Data Strobe Parallel Interface SpecificationsFig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible FontsAppendix OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 5P Mode Epson ModeIndex Paper lamp 6-1