Brother HL-1060 Series manual Test Print Mode, Lamp Lit Choice Function

Page 35

USER’S GUIDE

✒Note

∙When the printer goes into sleep mode, the fan will not stop until the printer engine has cooled down.

∙Sleep mode allows the print engine to cool, so the temperature of your room and how long the printer has been in sleep mode affects the warm-up time. This warm-up time can take up to 30 seconds. The Ready lamp blinks to indicate that the printer is warming up.

∙You can change the time out for the sleep mode with the supplied printer driver or Remote Printer Console program. Refer to the Help section in the printer driver or RPC program for more information about the sleep mode setting.

Test Print Mode

The printer has the following test print mode. Follow these steps:

1.Make sure that the top cover is closed.

2.Hold down the switch and turn on the power switch. Keep the switch depressed until the Drum lamp comes on.

The Drum lamp lights to indicate that the printer is in the test print mode.

3.Press the switch again to execute the test print or hold down the switch to select another option and release the switch to execute the selected option.

The test print mode varies depending upon the printer model as follows:

Lamp Lit	Choice	Function
Drum	Test sample page	The printer prints a test sample page.
		The printer returns to the ready status after
		printing.

Alarm	Print Config & Print	The printer prints the current configuration of the
	Fonts I	printer and a list of the internal fonts.
		The printer returns to the ready status after
		printing.

Ready	Factory Reset	The printer is restored to the factory setting and
		permanent fonts and macros are cleared.
		The printer returns to the ready status after
		printing.
Data	Hex Dump Print	The printer can print data as hexadecimal values,
		so that you can check data errors and problems.
		To exit from this mode, you have to turn off the
		printer.

CHAPTER 3 –4

Image 35

Contents Brother Laser Printer Please read this manual thoroughly before using the printerShipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice TrademarksTo Use the Printer Safely Definitions of Warnings, Cautions, and NotesTable of Contents Index International Energy Star Compliance Statement RegulationsIndustry Canada Compliance Statement For Canada Only FDA Regulations For 110-120 V Model Only Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model OnlyGeräuschemission / Acoustic Noise Emission For Germany Only Important For Your SafetyImportant Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the PrinterPrinter Overview About Your PrinterFeatures Enhanced Memory Management Remote Printer Console Program for DOSPopular Printer Emulation Support Low Running Cost Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Environment Power SupplyOperating and Storage Environment Introduction Paper Type Paper Size Paper SpecificationsUSER’S Guide Fan the Paper Straighten the Paper RemarksEnvelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the FeederMoving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing Manual Feed Slot When you load one sheet of paper manuallyWhen you load more than one sheet of paper manually Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support WireReady Paper Lamp Lamps and SwitchFeeder Lamp Data Toner LampDrum Lamp Sleep Mode Alarm LampSwitch Other Control FeaturesLamp Lit Choice Function Test Print ModeProtection Control Features Set by the Brother DriverAPT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100MSelecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface ParametersOff BitsBit DTR onlyNone Connecting the Serial Interface CableOptions BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional MemoryUnplug the power cord Disconnect the interface cable Installing the SimmRemove the main controller board Replacing the Toner Cartridge Chapter MaintenanceRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum UnitGently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed RollersRE-PACKING the Printer 26 Removing the Drum Unit Assembly27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a GlanceSimm Error ActionTroubleshooting NV-RAM Service CallsLocating Paper Jam Position Paper JamsPaper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer HardwareQuestion Setting Up the Printer for WindowsSetting Up the Printer for DOS When Using the Optional BR-Script 2 ROM Board BR-3000 Setting Up the Printer for Apple Macintosh ComputersWhen Using the Optional RS-100M Serial Interface Paper Handling Printing Together right now, over Print QualityToner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer SpecificationsFunctions Electrical and Mechanical Data Strobe Parallel Interface SpecificationsFig. A-1 Parallel Interface Cable Intellifont Compatible Fonts Resident FontsBitmapped Fonts Scalable FontsAppendix Epson Mode Symbol SETS/ Character SetsOCR Symbol Sets HP LaserJet 5P ModeIndex Paper lamp 6-1