Brother HL-1060 Series manual Paper Jam in the Feeders

Page 69

USER’S GUIDE

❏Paper Jam in the Multi-Purpose Sheet Feeder

If a paper jam has occurred inside the multi-purpose sheet feeder 1 or 2, pull the jammed paper upwards out of the feeder. Also, remove Feeder 1 and open the top cover to check that a torn piece of paper does not remain inside the printer: refer to the following sections.

Feeder 1

Feeder 2

Fig. 6-3 Paper Jam in the Feeders

If the paper cannot be pulled up, see the next sections “Paper Jam under

Feeder 1” and “Paper Jam near the Drum Unit.”

❏Paper Jam under Feeder 1

If a paper jam has occurred under the front multi-purpose sheet feeder 1, remove the feeder. ( ➀ ) Then, pull the jammed paper upwards and out of the printer. ( ➁ ) Re-install the feeder.

Fig. 6-4 Paper Jam under Feeder 1

CHAPTER 6 –6

Image 69

Contents Brother Laser Printer Please read this manual thoroughly before using the printerShipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice TrademarksTo Use the Printer Safely Definitions of Warnings, Cautions, and NotesTable of Contents Index Regulations Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model Only Radio Interference 220-240 V Model OnlyFDA Regulations For 110-120 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model OnlyGeräuschemission / Acoustic Noise Emission For Germany Only Important For Your SafetyImportant Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the PrinterPrinter Overview About Your PrinterFeatures Remote Printer Console Program for DOS Popular Printer Emulation SupportEnhanced Memory Management Environment-Friendly Economy Printing Mode Sleep Mode Power Save ModeLow Running Cost Power Supply Operating and Storage EnvironmentEnvironment Introduction Paper Type Paper Size Paper SpecificationsUSER’S Guide Fan the Paper Straighten the Paper RemarksEnvelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the FeederMoving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support WireReady Paper Lamp Lamps and SwitchData Toner Lamp Drum LampFeeder Lamp Switch Alarm LampOther Control Features Sleep ModeLamp Lit Choice Function Test Print ModeProtection Control Features Set by the Brother DriverAPT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100MSelecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface ParametersBit BitsDTR only OffNone Connecting the Serial Interface CableOptions BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional MemoryUnplug the power cord Disconnect the interface cable Installing the SimmRemove the main controller board Replacing the Toner Cartridge Chapter MaintenanceRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum UnitGently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed RollersRE-PACKING the Printer 26 Removing the Drum Unit Assembly27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a GlanceSimm Error ActionTroubleshooting NV-RAM Service CallsLocating Paper Jam Position Paper JamsPaper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer HardwareQuestion Setting Up the Printer for WindowsSetting Up the Printer for DOS Setting Up the Printer for Apple Macintosh Computers When Using the Optional RS-100M Serial InterfaceWhen Using the Optional BR-Script 2 ROM Board BR-3000 Paper Handling Printing Together right now, over Print QualityToner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer SpecificationsFunctions Electrical and Mechanical Data Strobe Parallel Interface SpecificationsFig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible FontsAppendix OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 5P Mode Epson ModeIndex Paper lamp 6-1