Brother HL-1060 Series manual Paper Jams, Locating Paper Jam Position

Page 68

CHAPTER 6 TROUBLESHOOTING

PAPER JAMS

Before you can clear a paper jam error, you need to find the location of the paper jam. Locate the position referring to the following figure.

Paper

Paper

Rear Multi-Purpose

Sheet Feeder 2

Drum Unit

Front Multi-Purpose Sheet Feeder 1 can be removed to clear paper jams

Top Cover

Fig. 6-1 Locating Paper Jam Position

After locating the position, clear the jammed paper referring to the following descriptions. If the jammed paper is removed completely and the top cover is closed, the printer may resume printing automatically. If the printer does not resume printing, press the control panel switch.

Warning

After you have just used the printer, some internal parts of the printer are extremely hot. When you open the top cover of the printer, never touch the shaded parts shown in the following diagram.

High Temperature

Fig. 6-2 Inside the Printer

CHAPTER 6 –5

Image 68

Contents Please read this manual thoroughly before using the printer Brother Laser PrinterShipment of the Printer Laser Printer HL-1060 Series User’s Guide Trademarks Compilation and Publication NoticeDefinitions of Warnings, Cautions, and Notes To Use the Printer SafelyTable of Contents Index International Energy Star Compliance Statement RegulationsIndustry Canada Compliance Statement For Canada Only FDA Regulations For 110-120 V Model Only Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only IEC 825 Specification For 220-240 V Model Only Declaration of Conformity For EuropeImportant For Your Safety Geräuschemission / Acoustic Noise Emission For Germany OnlyImportant Wiring Information For U.K. only Finding Out How to Use the Printer About the GuidebooksAbout Your Printer Printer OverviewFeatures Enhanced Memory Management Remote Printer Console Program for DOSPopular Printer Emulation Support Low Running Cost Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Environment Power SupplyOperating and Storage Environment Introduction Paper Specifications Paper Type Paper SizeUSER’S Guide Remarks Fan the Paper Straighten the PaperEnvelopes MULTI-PURPOSE Sheet Feeders Loading Paper into the Feeder Opening the Feeder and Moving the Paper GuidesMoving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing Manual Feed Slot When you load one sheet of paper manuallyWhen you load more than one sheet of paper manually Paper Handling Output Tray and Paper Support Wire You can stack up to 100 sheets in the output trayLamps and Switch Ready Paper LampFeeder Lamp Data Toner LampDrum Lamp Alarm Lamp SwitchOther Control Features Sleep ModeTest Print Mode Lamp Lit Choice FunctionControl Features Set by the Brother Driver ProtectionAPT Advanced Photoscale Technology Serial Interface Board RS100M Selecting the RS-422A Apple or RS-232C IBM Serial InterfaceSetting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial InterfaceBits BitDTR only OffConnecting the Serial Interface Cable NoneOptions BR-SCRIPT 2 ROM Board BR-3000 Additional Memory Minimum Memory Recommendation including resident memoryInstalling the Simm Unplug the power cord Disconnect the interface cableRemove the main controller board Chapter Maintenance Replacing the Toner CartridgeRemoving the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 20 Turning off the Switch and UnpluggingGently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire Cleaning the Paper Feed Rollers 24 Cleaning the Feeder 1 Paper Feed Rollers26 Removing the Drum Unit Assembly RE-PACKING the Printer27 Placing the Drum Unit in the Plastic Bag Alarm Indications AT a Glance Operator CallsError Action SimmTroubleshooting Service Calls NV-RAMPaper Jams Locating Paper Jam PositionPaper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Setting Up the Printer Hardware Question RecommendationSetting Up the Printer for Windows QuestionSetting Up the Printer for DOS When Using the Optional BR-Script 2 ROM Board BR-3000 Setting Up the Printer for Apple Macintosh ComputersWhen Using the Optional RS-100M Serial Interface Paper Handling Printing Print Quality Together right now, overToner scatters and stains the printed Printer Interior and Drum Unit Printer Specifications Appendix aFunctions Electrical and Mechanical Parallel Interface Specifications Data StrobeFig. A-1 Parallel Interface Cable Resident Fonts Bitmapped FontsScalable Fonts Intellifont Compatible FontsAppendix Symbol SETS/ Character Sets OCR Symbol SetsHP LaserJet 5P Mode Epson ModeIndex Paper lamp 6-1