D-Link DES-5024 manual Installing Modules

Page 22

Fast Ethernet Switching System User’s Guide

Installing Modules

The process for installing both optional modules is the same. You cannot change the position of the CPU module. The DES-5024 will not work unless the CPU module is installed in the CPU slot.

You can purchase optional modules separately in order to meet the needs of your network. The two optional modules available for the DES-5024 are: a 2-Port 100BASE- FX (fiber optic) module and a 1-Port 1000BASE-SX (gigabit) module. As shown in Figure 7, optional modules can only be installed in Slot 3. Nothing can be installed in slot

4.The procedure for installing modules is the same for all both modules. Follow these steps to install an optional module:

1.Power the DES-5024 off before installing the optional module. The optional modules are not hot swappable.

2.Remove the blank bracket, as shown in Figure 7, and set aside. Grasp the thumbscrews on the sides of the blank bracket and turn counterclockwise to unscrew them. You can also use a Phillips screwdriver to unscrew the blank bracket. Do not discard the blank bracket. Put the blank bracket back in if you remove the optional module.

3.Install the optional module by inserting it into the guide, see Figure 8, and sliding it in until it stops. Press in firmly until you feel the optional module snap into place. The optional module should be level and flush with the rest of the DES-5024. Never force, twist or bend the module. The optional module slides in smoothly.

4.Gently push the thumbscrews in and turn clockwise to tighten. Do not over tighten the thumbscrews.

5.Power the DES-5024 on after you have installed the optional module. The DES-5024 will auto detect the optional module.

6.Remove the dust cover from the transceiver and plug the cable in.

7.Check the LEDs to verify that there is a link and a proper connection at the port.

See the Troubleshooting section if the optional module is not working properly.

Installing the DES-5024

14

Image 22

Contents DES-5024 Fast Ethernet Switching System User’s Guide Link Limited Warranty Hardware North, Central, and South America Copyright Statement Wichtige Sicherheitshinweise Table of Contents Page Page Audience About This GuideOrganization Features IntroductionPage Front Panel DES-5024 Front PanelRear Panel DES-5024 Rear PanelLocal Console Management Management MethodsUpdating Firmware Telnet ManagementInstalling the DES-5024 Unpacking the DES-5024Installation Options Desktop/ Shelf Installation Install Feet on BottomAttach Feet Rack Installation Attach Mounting Brackets Insert into Rack Installing Modules Remove Blank Bracket Insert Optional Module Power On Cable Specifications Connecting the DES-5024 to the NetworkCopper Cable Cable Diagram Fiber Optic Cable Fiber Optic Ports PortsMDI-X Ports RS-232 PortConnecting the DES-5024 to other Switches and Hubs DES-5024 to DES-5024 ConnectionLEDs DES-5024 LEDsPower CPU ModuleLED Port 10/100-TX Module LinkPort 100BASE-FX Module ColLit Dark Port 1000BASE-SX Module ActManaging the DES-5024 Local Console Management ∙ Data bits ∙ Parity None ∙ Stop bits ∙ Flow Control NoneTelnet ∙ Default User Name D-Link ∙ Default Password D-Link LogHelp Message Help MessagePanel Conventions SpacebarConsole Program System ConfigurationUser Account Management Snmp Management Configuration 100BASE-FX/ 1000BASE-SX Switch Port ModuleSpanning Tree Configuration Vlan Port ManagementFactory Reset to Default Config Values System Configuration MenuSystem Reset System InformationSystem Information Menu Software UpdateBoot Prom Firmware Version Hardware RevisionSystem Description LAN Default GatewayMAC Address System NameSystem Reset System ResetFactory Reset Factory ResetFactory Reset confirmation Advantages of Store and Forward System Rate ControlDisadvantages of Store and Forward Advantages of Cut-Through Disadvantages of Cut-ThroughSoftware Update Menu Software Update menuTransfer Firmware Xmodem User Account Management User Account Change MenuAccess Level PasswordConfirm Password Create New UserPage Status Delete UsersDelete Page Old Password Change PasswordNew Password Page Switch Port Configuration State Switch Port Configuration MenuPhysical Priority Port StateFlow Control Spanning Tree Configuration Menu Spanning Tree ConfigurationSTA Operation Levels Bridge Priority Forward Delay TimeSpanning Tree Algorithm Root CostRoot Bridge Root PortSnmp Management Configuration Access Right Snmp Management Configuration MenuSnmp Manager Setting Snmp Community StringCold Start Snmp Trap Manager SettingAuthentication Failure Link Change EventPage Vlan Port Management Vlan Port Management Menu Vlan Port Management menuPort # Create New VlanNew Vlan Name TrunkGroupPage Delete Vlan Menu Vlan NameModify Vlan Menu Virtual LAN NameTrunking Port Management Menu Trunking Port Management menuNew Trunking Group Name Create New Trunking PortName Page Trunking Port Delete Trunking PortModify Trunking Port Trunking Port Name Modify Trunking PortTroubleshooting ProblemSolutionPage Diagnostic LED Switch Specifications Appendix a DES-5024 Technical SpecificationsPort Specifications 10BASE-T EMI Fast Ethernet Switching System User’s Guide Performance Access Level IndexUser Name 50, 52