D-Link DES-5024 manual MDI-X Ports, Fiber Optic Ports, RS-232 Port

Page 29

Fast Ethernet Switching System User’s Guide

Ports

MDI-X Ports

MDI-X ports are crossover ports. The pin arrangement is the same as the arrangement in a crossover cable. The advantage of MDI-X ports is that you can connect a device with an MDI-II port without using a crossover cable. The steps for connecting the DES-5024 to 10 Mbps devices or 100 Mbps devices are the same. All the ports will auto negotiate the proper speed and duplex mode. The DES-5024 has two full sized modules with 12 ports each and one half size optional module.

Follow these steps to connect cables to the DES-5024:

Check for the appropriate cable configuration for each device.

1.Plug one end of the cable into any of the MDI-X ports.

2.Plug the other end into the appropriate port on the other device.

3.Verify that the LED indicates connection at the proper speed and duplex mode.

Fiber Optic Ports

The DES-5024 supports 100BASE-FX and 1000BASE-SX. The ports are on modules that you can install in the chassis. The chassis supports a 2-Port 100BASE-FX optional module. The ports support full and half duplex at 100 Mbps. The ports do not support 10 Mbps.

A 1-Port 1000BASE-SX optional module is available. The 1-Port 1000BASE-SX optional module only supports full duplex at 1000 Mbps. Contact D-Link, Inc. sales to purchase any of the modules.

Refer to Chapter 3, Installing Optional Modules, for installation instructions. Refer to Chapter 3, Cable Specifications, for information on cable types and connectors.

RS-232 Port

Follow these steps to connect the DES-5024 and another device:

1.Plug one end of the cable provided into the port.

2.Plug the other end into the PC.

3.Run HyperTerminal or a terminal emulation program using the settings given for Local Console Management at the beginning of Chapter 5, Managing the DES-5024.

Connecting the DES-5024 to the Network

21

Image 29
Contents DES-5024 Fast Ethernet Switching System User’s Guide Link Limited Warranty Hardware North, Central, and South America Copyright Statement Wichtige Sicherheitshinweise Table of Contents Page Page Organization About This GuideAudience Introduction FeaturesPage DES-5024 Front Panel Front PanelDES-5024 Rear Panel Rear PanelUpdating Firmware Management MethodsLocal Console Management Telnet ManagementUnpacking the DES-5024 Installing the DES-5024Installation Options Install Feet on Bottom Desktop/ Shelf InstallationAttach Feet Rack Installation Attach Mounting Brackets Insert into Rack Installing Modules Remove Blank Bracket Insert Optional Module Power On Copper Cable Connecting the DES-5024 to the NetworkCable Specifications Cable Diagram Fiber Optic Cable MDI-X Ports PortsFiber Optic Ports RS-232 PortDES-5024 to DES-5024 Connection Connecting the DES-5024 to other Switches and HubsDES-5024 LEDs LEDsCPU Module PowerLED Link Port 10/100-TX ModuleCol Port 100BASE-FX ModuleLit Dark Act Port 1000BASE-SX ModuleManaging the DES-5024 ∙ Data bits ∙ Parity None ∙ Stop bits ∙ Flow Control None Local Console ManagementTelnet Log ∙ Default User Name D-Link ∙ Default Password D-LinkHelp Message Help MessageSpacebar Panel ConventionsUser Account Management System ConfigurationConsole Program Spanning Tree Configuration 100BASE-FX/ 1000BASE-SX Switch Port ModuleSnmp Management Configuration Vlan Port ManagementSystem Reset System Configuration MenuFactory Reset to Default Config Values System InformationBoot Prom Firmware Version Software UpdateSystem Information Menu Hardware RevisionMAC Address LAN Default GatewaySystem Description System NameSystem Reset System ResetFactory Reset Factory ResetFactory Reset confirmation Disadvantages of Store and Forward System Rate ControlAdvantages of Store and Forward Disadvantages of Cut-Through Advantages of Cut-ThroughSoftware Update menu Software Update MenuTransfer Firmware Xmodem User Account Change Menu User Account ManagementConfirm Password PasswordAccess Level Create New UserPage Delete Delete UsersStatus Page New Password Change PasswordOld Password Page Switch Port Configuration Physical Switch Port Configuration MenuState Flow Control Port StatePriority STA Operation Levels Spanning Tree ConfigurationSpanning Tree Configuration Menu Spanning Tree Algorithm Forward Delay TimeBridge Priority Root CostRoot Port Root BridgeSnmp Management Configuration Snmp Manager Setting Snmp Management Configuration MenuAccess Right Snmp Community StringAuthentication Failure Snmp Trap Manager SettingCold Start Link Change EventPage Vlan Port Management Vlan Port Management menu Vlan Port Management MenuNew Vlan Name Create New VlanPort # TrunkGroupPage Vlan Name Delete Vlan MenuVirtual LAN Name Modify Vlan MenuTrunking Port Management menu Trunking Port Management MenuName Create New Trunking PortNew Trunking Group Name Page Modify Trunking Port Delete Trunking PortTrunking Port Modify Trunking Port Trunking Port NameProblemSolution TroubleshootingPage Diagnostic LED Port Specifications Appendix a DES-5024 Technical SpecificationsSwitch Specifications 10BASE-T EMI Fast Ethernet Switching System User’s Guide Performance Index Access LevelUser Name 50, 52