3Com 3CR990 manual Go to 3Com DOS Configuration Program, Windows

Page 28
Go to: 3Com DOS Configuration Program.

28CHAPTER 4: WINDOWS DRIVERS

10Select the CD-ROM drives option, clear any other checked options, and click Next.

The Driver Files Search Results screen appears. Windows finds the driver on the CD.

11Click Next.

Files are copied, and then the message “Windows has finished installing the software for this device” appears.

12Click Finish.

The software installation is complete. To verify that the installation was successful Go to: Verifying Successful Installation.

To change configuration settings

Go to: 3Com DOS Configuration Program.

Windows 98

This section describes how to install the network driver and NIC software in a PC

 

or server running Windows 98.

Before installing the NIC software:

Make sure that the NIC is installed in the PC and connected to the network.

Make sure that you have the Windows 98 installation files. These files may be on a CD or diskettes, or they may have been copied to your hard disk when Windows 98 was installed on your PC.

NOTE: If you encounter problems during the installation, see TROUBLE.TXT (located in the HELP directory on the EtherCD) for troubleshooting tips.

To install the software:

1Turn the PC power on.

Windows detects the NIC. The Add New Hardware Wizard starts.

2Click Next.

The Add New Hardware Wizard screen prompts you to select an option.

3Select the Search for the best driver for your device (Recommended) option, and then click Next.

The Add New Hardware Wizard screen prompts you for the driver location.

4Select the CD-ROM drive option and clear any other check options that are selected.

5Insert the EtherCD in the CD-ROM drive, and then click Next. Windows finds the driver file for the device.

6Click Next. Files are copied.

The Insert Disk screen appears, prompting you for the Windows 98 CD-ROM.

Image 28
Contents 3CR990 Family of EtherLink NICs EtherLink 10/100 PCI Network Interface Card with 3XP processorUser Guide Published August3Com Corporation 5400 Bayfront Plaza SantaClara, California UNITED STATES GOVERNMENT LEGENDCONTENTS 3 NIC INSTALLATION2 3CR990 NICS 1 BEFORE YOU BEGIN4 WINDOWS DRIVERS 5 NETWARE DRIVERS6 IP SECURITY Multiple NICs8 CONFIGURATION 9 TROUBLESHOOTING7 UPGRADING DRIVERS Accessing the 3Com KnowledgeBaseE MBA BOOT ROM A SPECIFICATIONSD UNINSTALLING NIC SOFTWARE B TECHNICAL SUPPORTF DYNAMICACCESS TECHNOLOGY INDEX WARRANTY AND REGULATORY COMPLIANCE INFORMATIONDynamicAccess Features Configuring DynamicAccess TechnologyPage BEFORE YOU BEGIN 2 Click Register Product, and then Register OnlineGo to Auto Insert Go to Root Subdirectories 1 Right-click the My Computer icon, and then select Properties click NIC Software, Drivers and Diagnostics, NIC Preinstallation NIC Installation with Windows 2000, and then DoneGo to NIC Installation Minimum SystemDOS-Bootable Diskette Installationto install these drivers about installation diskettesInstallations \ Diskette.pdf To make installation diskettes 3CR990 NICS NIC OverviewNIC Features Encryption chip Remote Wake-Up RWU connector 3XP processor3CR990 NICs support up to 168-bit 3DES encryptionNOTE The 3CR990 NICs provide a network connection with or without the Remote Wake-Up cable installedUpgrading software Scanning for viruses Offload Features DynamicAccess Technology, and Install 3Com DMI Agent nowOffline Diagnostics Windows2 Click the Local Area Connection icon NOTE The default hex value is F all offloads enabled3 Click Configure 20 CHAPTER 2 3CR990 NICS NIC INSTALLATION Installing the NICyour system For more information22 CHAPTER 3 NIC INSTALLATION Installing the NIC Remote Wake-Up Cable24 CHAPTER 3 NIC INSTALLATION DATATX ACT L N KWhat do you want to do? Go to Windows Go to Windows Go to Windows NT Go to Windows NTGo to NetWare Drivers Go to Multiple NICsPage Windows 2000 and installed the NIC, go to step 7 in this procedure 3 Click Drivers and Diagnostics4 Click NIC Preinstallation 5 Click NIC Installation with Windows 2000, and then click DoneGo to 3Com DOS Configuration Program NOTE You must restart your computer to complete the installation To verify that the installation was successfulGo to Verifying Successful Installation Go to New Hardware Found Go to Update Device Driver WizardGo to Verifying Successful Installation Driver Wizard Update DeviceWindows NT Windows NTPC or server running Windows NT 4 Click Add Adapter a Select the Enable Automatic DHCP Configuration check box6 Click Continue Verifying Successful Installation34 CHAPTER 4 WINDOWS DRIVERS Multiple NICs 5 Click NIC Installation with Windows 2000, and then Doneoperating system Windows 95 and 36 CHAPTER 4 WINDOWS DRIVERS5 Click Have Disk Page NETWARE DRIVERS NOTE 3CR990 NICs do not support NetWare 3.11 and 4.0x servers4.11, and Go to Verifying the PCI Slot NumberFor NetWare a Select Reinitialize SystemVerifying the PCI Slot Number load c\nwserver\3c99x.lanIP SECURITY Overview Creating a Security Policy5 Select IP Security Policy Management, and then click Add 7 Clear the Activate the default response rule check box1 In the left pane, click IP Security Policies on Local Machine Filter Action Creating a Security Policy2 Select Un-assign 46 CHAPTER 6 IP SECURITYUPGRADING DRIVERS 8 Click Have DiskGo to Windows 95 Version A Build Go to Windows 98 and Windows6 Click Close 7 Click Have DiskWindows NT 4.0 6 Click Restart Now 50 CHAPTER 7 UPGRADING DRIVERSProvides the ability to boot a PC CONFIGURATION100BASE-TX 100 Mb/s If you do not have a DOS-bootable diskette Go to Making a DOS-Bootable Diskette3Com DOS ConfigurationDiagnostics Program Diagnostics Program3Com NIC Go to To Run the Network Test5 Repeat the process for each setting that you want to change TROUBLESHOOTING Accessing theTroubleshooting the InstallationRunning Diagnostics ProgramsGo to 10BASE-T Description Go to 100BASE-TX Description Go to Technical SupportFor more information about how to make a DOS-bootable diskette 4 Click 3Com NIC DoctorGeneral Tab Configuration TabDiagnostics Tests Diagnostics TabFlash Update Tab Accessing the 3ComTo run the NIC test, Network test, or Remote Wake-Up test 2 Click Perform NIC Test Accessing 3Com Support ServicesGo to Troubleshooting Remote Wake-Up Go to 3Com NIC Diagnostics ProgramRemote Wake-Up 3Com Tray Iconconnection between the NIC and the network Network Connection Troubleshooting aNOTE For more information on PCI specifications and Remote Wake-Up 2 Connect a straight-through cable from the PC to the hub SPECIFICATIONS NIC SpecificationsPCI Local Bus Specification, Revision HardwareConnection Criteria NetworkNetwork Cable 1 TD+ 2 TD 3 RD+ 6 RD Assignments1 2 3 4 5 6 7 Pause Frames Flow ControlLink Negotiation Services TECHNICAL SUPPORTRegister this Product Online Technical1 408 727 1 847day, 7 days a week Country Support from 3ComTelephone Number To obtain an RMA number, call or fax over-the-network installations SUPPORTED DRIVERSAdditional Drivers NOTE DOS drivers are not supported for 3CR990 NICs. However, they arePage Windows 98 and UNINSTALLING NIC SOFTWAREor Windows 76 APPENDIX D UNINSTALLING NIC SOFTWARE MBA BOOT ROM the Boot ROM SettingBooting with the MBA Boot ROMMBA boot ROM, see the documentation that came with MBA on the EtherCD Non-BBSDYNAMICACCESS TECHNOLOGY DynamicAccessFeatures Failure to install the patch will result in system failureInstalling Technologyyou install the NIC software To install DynamicAccess technologyConfiguring NOTE You must restart your PC to complete the installationmanagement tools for an Ethernet network Removing 1 Double-click the Add/Remove Programs icon in the Control Panel2 Select the DAPassThru Driver Transport protocol Page INDEX Numbersuninstalling NIC software 76 unshielded twisted pair UTP 3Com Corporation Limited Warranty WARRANTY AND REGULATORY COMPLIANCE INFORMATIONYEAR 2000 WARRANTY OBTAINING WARRANTY SERVICERegulatory Compliance Information LIMITATION OF LIABILITYDISCLAIMER GOVERNING LAW3COM END USER SOFTWARE IMPORTANT Read Before Using This Product INDUSTRY CANADA CLASS BEMISSION COMPLIANCE STATEMENT3Com Corporation 5400 Bayfront Plaza P.O. Box Santa Clara, CA 95052-8145 408