Actiontec electronic GT701 Regulatory Compliance Notices, Modifications, Class B Equipment

Page 104

Notices

Regulatory Compliance Notices

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures:

sReorient or relocate the receiving antenna;

sIncrease the separation between the equipment and receiver;

sConnect the equipment to an outlet on a circuit different from that to which the receiver is connected;

sConsult the dealer or an experienced radio or television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc., may void the user’s authority to operate the equipment.

Declaration of conformity for products marked with the FCC logo – United States only.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions:

1. This device may not cause harmful interference;

101

Image 104

Contents DSL Modem Table of Contents Setting Up Static IP on the Computer SpecificationsGlossary Firewall Security Level Services Table Non-Windows System SetupPackage Contents Introduction1Features Minimum System RequirementsGetting to Know the Modem Power Light DSL LightInternet Light Ethernet LightPhone Port Phone port is used to connect the Modem to a phone jackUSB Port Ethernet PortOn/Off Switch Reset ButtonPower Port Power port is used to connect the Power cord to the ModemConnecting Via Ethernet Setting Up ModemConnecting a Computer to the Modem Page Setting Up the Modem Page Setting Up the Modem Page Setting Up the Modem Page Setting Up the Modem Page Setting Up the Modem Page Setting Up the Modem Page Installing Phone Filters Remove the phone filters from the clear bag. Click Next Setting Up the Modem USB Click NextNext, go to Setting Up the DSL Connection on the next Setting Up the DSL Connection Setting Up the Modem Installation Buddy checks the configuration of the Modem Modem is successfully configured and ready for usePerforming a Basic Setup Basic SetupPage Performing a Basic Setup Changing the Admin User Name and Password Click Save and Restart at the bottom of the screenTo access the Advanced Settings configuration screens Using Advanced SetupAccessing Advanced Setup WAN IP Address Transparent Bridging PPP Auto Connect Encapsulation PPPoA only Specify a Static IP Address LAN IP Address Dhcp Server DNS Dynamic or Static Beginning IP AddressEnding IP Address Services Blocking DNS ServerWebsite Blocking Remote Management Port ForwardingUsing Advanced Setup DMZ Hosting FirewallDynamic Routing NAT Network Address TranslationStatic Routing Viewing Modem’s Settings StatusPage Routing Table WAN StatusLAN Status Active User ListUsing Utilities Web Activity LogDSL Settings Restore Default SettingsUpgrade Firmware This page left intentionally blank Troubleshooting TroubleshootingCannot Use the Internet Physical ConnectionsFrequently Asked Questions Connection to the InternetWhich protocols does the Modem support? Which connection speeds does the Modem support?Is the Modem flash-upgradeable? How do I do it? What is the valid IP range I can use for my home network?How do I find out which IP address my computer is using? Will my Xbox work with the Modem?Yes, if the application is designed to run over a network What is the default username for the Modem? What is NAT and how does it protect my network?How many computers can be connected through the Modem? Does the Modem function as a firewall?This page left intentionally blank Reference Locating Computer InformationLocating Windows Operating System Files Appendix a Reference Click Search Setting Up Static IP On the Computer Windows 98 SEPage 192.168.0.2 Windows Me Enter the following address in the Subnet mask text boxAppendix B Setting Up Static IP on the Computer 192.168.0.2 Windows Page Appendix B Setting Up Static IP on the Computer 192.168.0.2 Windows XP Page Appendix B Setting Up Static IP on the Computer 192.168.0.2 Comparing DSL Service with a Dial-Up Modem Computer SecurityWeb Browsers Modem SecurityComputer Security Electronic Security This page left intentionally blank Specifications D GeneralEnvironmental LED IndicatorsPower, DSL, Internet, Ethernet, USB Access Point GlossaryPage Ssid This page left intentionally blank Firewall Security Level Services Table High Security LevelMedium Security Level Low Security LevelService Acronym Definitions Basic Security LevelReal audio/video Icmp323 120Non-Windows G System Setup ClassicPage Appendix G Non-Windows Setup Page Installation Buddy Settings 100 Class B Equipment Regulatory Compliance NoticesModifications Miscellaneous Legal Notices All other names are the property of their respective ownersLimited Warranty 103104 Limited Warranty 106 Index 108 Index 110 111 112