Cisco Systems CTSMX30055K9 manual Conference 1..1 MicUnmuteOnDisconnect Mode

Page 37

Cisco TelePresence MX Series

Administrator guide

Table of contents

Introduction

Web interface

Advanced settings

Appendices

 

37

 

 

Conference [1..1] MicUnmuteOnDisconnect Mode

Determine if the microphones shall be unmuted automatically when all calls are disconnected. In a meeting room or other shared resources this could be done to prepare the system for the next user.

Requires user role: ADMIN

Value space: <On/Off>

On: Un-mute the microphones after the call is disconnected.

Off: If muted, let the microphones remain muted after the call is disconnected.

Example: Conference 1 MicUnmuteOnDisconnect Mode: On

Conference [1..1] DoNotDisturb Mode

Determine if there should be an alert on incoming calls.

Requires user role: USER

Value space: <On/Off>

On: All incoming calls will be rejected, with no alert. The calling side will receive a busy signal when trying to call the codec. A message will display on screen, telling that Do not disturb is turned on, together with an option to turn off the Do not disturb. When turning off the Do not disturb mode you will see a list of the calls that have been rejected.

Off: The incoming calls will be alerted.

Example: DoNotDisturb Mode: Off

Conference [1..1] Encryption Mode

Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption Off" displays on screen for a few seconds when the conference starts.

Requires user role: ADMIN

Value space: <BestEffort/On/Off>

BestEffort: The system will use encryption whenever possible.

>In Point to point calls: If the far end system supports encryption (AES-128), the call will be encrypted. If not, the call will proceed without encryption.

>In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support encryption. If not, the conference will be unencrypted.

On: The system will only allow calls that are encrypted.

Off: The system will not use encryption.

Example: Conference 1 Encryption Mode: BestEffort

Conference [1..1] DefaultCall Protocol

Set the Default Call Protocol to be used when placing calls from the system.

Requires user role: ADMIN

Value space: <H323/Sip>

H.323: Select H.323 to ensure that calls are set up as H.323 calls.

Sip: Select SIP to ensure that calls are set up as SIP calls.

Example: Conference 1 DefaultCall Protocol: H323

Conference [1..1] FarEndControl Mode

Lets you decide if the remote side (far end) should be allowed to select your video sources and control your local camera (pan, tilt, zoom).

Requires user role: ADMIN

Value space: <On/Off>

On: Allows the far end to be able to select your video sources and control your local camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as normal.

Off: The far end is not allowed to select your video sources or to control your local camera (pan, tilt, zoom).

Example: Conference 1 FarEndControl Mode: On

Conference [1..1] FarEndControl SignalCapability

Set the far end control (H.224) signal capability mode.

Requires user role: ADMIN

Value space: <On/Off>

On: Enable the far end control signal capability.

Off: Disable the far end control signal capability.

Example: Conference 1 FarEndControl SignalCapability: On

Conference [1..1] DefaultCall Rate

Set the Default Call Rate to be used when placing calls from the system.

Requires user role: ADMIN

Value space: <64..6000>

Range: Select a value between 64 and 6000 kbps

Example: Conference 1 DefaultCall Rate: 768

Conference [1..1] MaxTransmitCallRate

Specify the maximum transmit call rate to be used when placing or receiving calls.

Requires user role: ADMIN

Value space: <64..6000>

Range: Select a value between 64 and 6000 kbps.

Example: Conference 1 MaxTransmitCallRate: 6000

D14850.02 MX Series Administrator Guide (TC5.0) 2011 NOVEMBER © 2011 Cisco Systems, Inc. All rights reserved.

www.cisco.com

Image 37
Contents MX300 MX200 Cisco TelePresence MX SeriesCisco TelePresence MX Series Table of contentsIntroduction Intellectual property rights Cisco contacts User documentationSoftware Products covered in this guideWhat’s new­in this version Software download New features and improvementsSoftware release notes Other enhancements Advanced configuration menu changesCisco TelePresence MX Series at a glance Features and benefitsCisco TelePresence MX Series Web interface Connect to the video system Starting the web interfaceSign Sign outClick your user name Open the Change Password dialog box Changing the system/codec passwordSet the new password Enter passwordsMenu availability and user roles Interactive menuMain menu Open sub-pagesSystem information System information Login informationLog files XML files Changing system settings Advanced configurationSearch functionality Select a wallpaper Selecting a wallpaperUpload a custom wallpaper file Enter the text message An active sign in banner Sign in bannerPlacing calls Sharing contentsCalling someone Address input fieldControlling and monitoring a call Select a layout Local layout controlTaking snapshots Enabling the live snapshot featureMain source Display area Take live snapshots Upgrading the system software Uploading the trusted CA certificates list Certificate managementUploading the SSL certificate Audit certificate list Enable secure audit loggingAbout audit logging Upload the audit certificate listDefault user account User administrationSecurity mode About user rolesEditing user details Creating a new user accountDeactivating a user account Deleting a user accountRestarting the system Advanced settings Find the IP address of your system Open the web interface Overview of the advanced settingsNetworkServices SSH AllowPublicKey Cisco TelePresence MX Series Audio settings Cameras settings Conference settings Conference 1..1 DoNotDisturb Mode Conference 1..1 MicUnmuteOnDisconnect ModeConference 1..1 Encryption Mode Conference 1..1 DefaultCall ProtocolConference 1..1 PacketLossResilience Mode Conference 1..1 VideoBandwidth ModeConference 1..1 VideoBandwidth MainChannel Weight Conference 1..1 IncomingMultisiteCall ModeH323 settings H323 Profile 1..1 Gatekeeper Discovery H323 Profile 1..1 CallSetup ModeH323 Profile 1..1 Gatekeeper Address H323 Profile 1..1 H323Alias E164Network settings Network 1..1 QoS Diffserv Signalling Network 1..1 QoS ModeNetwork 1..1 IPv6 Gateway Network 1..1 IPv6 AssignmentNetwork 1..1 IEEE8021X Password Network 1..1 IEEE8021X ModeNetwork 1..1 QoS Diffserv Video Network 1..1 IEEE8021X TlsVerifyNetwork 1..1 RemoteAccess Allow Network 1..1 TrafficControl ModeNetwork 1..1 IEEE8021X Eap Md5 Network 1..1 IEEE8021X Eap TtlsNetworkServices settings NetworkServices Https Ocsp Mode NetworkServices Http ModeNetworkServices Https Mode NetworkServices Https VerifyServerCertificateNetworkServices SIP Mode NetworkServices NTP AddressNetworkServices Snmp CommunityName NetworkServices Snmp SystemContactPhonebook settings Provisioning settings RTP settings Security settings SIP settings SerialPort settingsSIP Profile 1..1 TlsVerify SIP Profile 1..1 DefaultTransportSIP Profile 1..1 Outbound SIP Profile 1..1 Proxy 1..4 AddressStandby settings SystemUnit settings Time TimeFormat Time settingsTime Zone Time DateFormatVideo settings UserInterface settingsVideo Input Source 1..2 CameraControl CameraId Video Input Source 1..2 CameraControl ModeVideo Input Source 1..2 OptimalDefinition Profile Video Input Source 1..2 OptimalDefinition Threshold60fpsVideo Input Source 1..2 Quality Video DefaultPresentationSourceVideo Input DVI 1 Type Video ControlPanel BrightnessVideo OSD LoginRequired Video OSD ModeVideo Layout LocalLayoutFamily Video Layout RemoteLayoutFamilyVideo AllowWebSnapshots Video Output LCD 1 ResolutionVideo Output LCD 1 MonitorRole Video Output LCD 1 BrightnessVideo WallPaper Experimental settingsExperimental CapsetFilter Experimental CapsetReductionExperimental NetworkServices UPnP Mode Experimental CTMSSupport ModeExperimental NetworkServices UPnP Timeout Experimental Conference 1..1 ReceiverBasedDownspeedingExample Experimental SystemUnit CrashReporting Mode Off Experimental SystemUnit CrashReporting ModeExperimental SystemUnit CrashReporting URI Example Experimental SystemUnit CrashReporting URIAppendices Setting the Administrator settings menu password Setting the system passwordSetting a root password Cisco VCS provisioning Downloading the provisioning configuration templateOptimal definition for systems supporting 1080p Optimal definition profilesClearPath Packet loss resilience DVI-I Technical specification for MX300/MX200SIP Web interface Advanced settings Document categories User documentation on the Cisco web site
Related manuals
Manual 2 pages 49.92 Kb

CTSMX30055K9 specifications

Cisco Systems has long been recognized as a leader in networking and communication technologies, and the Cisco TelePresence MX300 (CTSMX30055K9) exemplifies the company’s commitment to fostering exceptional video collaboration solutions. The MX300 is particularly designed for medium-sized meeting rooms, making it an ideal choice for enterprises looking to enhance their videoconferencing capabilities.

One of the standout features of the Cisco MX300 is its remarkable video experience. With support for up to 1080p high-definition video at 30 frames per second, users can enjoy crisp and clear visual quality during meetings. This resolution ensures that participants feel as though they are in the same room, regardless of their physical location. The MX300 also includes advanced video processing technology, which helps optimize picture quality even in varying bandwidth conditions.

In terms of audio, the MX300 is equipped with Cisco's intelligent audio technology. It utilizes multiple microphones and smart processing to ensure that all voices in the room are captured clearly, eliminating unwanted background noise. This results in a natural conversational experience, allowing for seamless interactions among participants.

Another significant characteristic of the MX300 is its user-friendly interface. The device comes with a simple remote control and touchscreen capabilities that make it easy for users to initiate calls, share content, and manage meetings. Integration with Cisco's Webex platform further enhances its usability, allowing users to join meetings with just one click.

The MX300 is known for its flexibility and scalability. It can be easily integrated into an existing IT infrastructure, supporting various endpoints and devices, which contributes to a more cohesive video collaboration experience. Additionally, it features interoperability with other video conferencing systems, ensuring that organizations can connect with partners and clients regardless of their technology stack.

Security is another strong suit of the Cisco MX300. The device incorporates robust security protocols, including encryption and secure access controls, safeguarding sensitive information shared during meetings. This emphasis on security is critical for organizations seeking to maintain compliance and protect their data.

Overall, the Cisco TelePresence MX300 (CTSMX30055K9) is a powerful solution for medium-sized meeting rooms, offering high-definition video, intelligent audio processing, and a user-friendly interface. With its flexibility, scalability, and strong security features, the MX300 stands out as an ideal choice for organizations committed to effective communication and collaboration. By enhancing the quality of virtual meetings, Cisco's MX300 continues to play a vital role in transforming the workplace into an environment where ideas can be shared effortlessly, fostering innovation and productivity.