ADIC Version 5.0 manual Installation & Acceptance, Use & Training, Responsibility

Page 8

Installing VolServ

Responsibility

Installation & Acceptance

Installation

Acceptance

Use & Training

Licensee has sole responsibility for use of the program and any information entered, used, or stored thereon. This responsibility includes protection of data from modification, destruction, or disclosure, and for the accuracy and integrity of the results from improper use. ADIC assumes no responsibility for Licensee’s negligence or failure to protect data from modification, destruction, or disclosure not specifically authorized in writing by ADIC.

Licensee shall, at its own expense, ensure that the installation site conforms to the requirements of the Software and, at its own expense, shall prepare and maintain the environmental conditions at the installation site in accordance with the requirements of the relevant hardware manufacturer. ADIC will be responsible for reasonable installation and support during the initial installation process.

Within 30 days of installation by ADIC, Licensee shall notify ADIC in writing of any defects in the Software. If Licensee does not notify ADIC within 30 days, the Software shall be deemed accepted by Licensee and payment shall be made. Where Licensee provides notice of defects, ADIC shall attempt to correct such defects within a reasonable time. If ADIC cannot correct material defects in the Software within 90 days of the date of installation, Licensee shall have, as a sole and complete remedy for failure to make such correction, the right to return the Software and related products sold under the same Purchase Agreement for a full refund.

Licensee shall limit the use of the Software to those individuals who have been appropriately trained. ADIC shall make training for the Software available to Licensee pursuant to its standard training procedures. ADIC shall provide “hands-on” training for Licensee’s personnel in the use of the Software at the time the Software is installed. Unless otherwise mutually agreed, any additional training will be provided at ADIC’s Englewood, Colorado facility at ADIC’s current rates.

viii	License Agreement

Image 8

Contents Installing VolServ VolServ Version September Rev aTrademark Notice East Peakview Ave Englewood, CO 80111 USA Phone FAXReader Comment Form Question Circle OnePage Premise of This License Terms Definitions Software LicensePrice Payment Use Copying Transfer RightsProtections ADIC’s WarrantyOwnership & Protection Installation & Acceptance Installation AcceptanceUse & Training ResponsibilityWarranty Servicing Warranty & ServicingWarranty Maintenance Infringement IndemnificationTermination Correspon- dence Disclaimer Limitation Liability AdicGeneral Entirety Contents Post Installation Tasks Preface Preface Purpose This BookWho Should Read This Book How This Book is OrganizedConventions Conventions used throughout the VolServ technical booksAre listed below Convention ExampleBooks Online BooksRelated PublicationsContact Publications Department Secured Web Site Publications described in the table below are createdStarted Roadmap Topic Refer ToInstallation Prior toTasks below are presented as guidelines only since Actual steps for your specific site are uniqueDirectory Contents VolServ Directory StructureMost cases, changes made to the *.config System Parameters Checklist Information Needed Default Customer EntryCreate VolServ Directories Name Description Path PermissionsConfigure EnvironmentWhere Option DescriptionUsernamepassworduidgidinformationlogindirectoryloginshell Change the /etc/shadow file access mode to Run the passwd command to initialize the vsadm passwordOn Sun, use the following command Obtain VolServ License StringsInstalling VolServ Installation Procedures Installation Procedures Running Installation Script Distribution MediaInstalling VolServ Step Task Refer to Installation SummaryFollowing steps are required for a successful installation Extract Files from CD To start extracting the VolServ files, press Depends on platforms and media typeInstall VolServ VolServ creates the volserv subdirectory Root directory TipInstalling VolServ Parameters Checklist on Installing VolServ Example below, a Scsi library is being installed VolServ database Linter is installed under $VSDIR/linter Procedures Either accept the default path or enter a new pathname Procedures Installing VolServ Post Installation Tasks Post Installation Tasks Post Installation Topics Put LinterStart and Stop Linter As the root user, run startlinter to startClose all Linter Database processes by running shutlinter To edit the Linter backup script, follow the steps belowBack Up the Database Location Journal Check PointingDatabase Database Recovery ManagementSite-Specific Topics Modifying Cshrc FileAdditional tasks include the following topics Cycle vsadm to pick up the changesConfiguring Scsi Device Nodes SGI/IRIX HostHere is an example of the report from hinv Solaris Host Access an OK prompt by simultaneously pressing Edit the /kernel/drv/sgen.conf file as shown BelowThis file to support Adic Media Changers libraries Stop key and the a key from a terminalReboot the Solaris host machine using boot -r to Force re-configuration of hardware devices. This willAt the OK prompt, enter boot to reboot the system Create the device node required for the attachedChange to the $VSDIR/config subdirectory Configuring for FileServChanging Configuration File Edit the appropriate *.config files Config File DescriptionTasks Servers.config Configuring Label PrintersConfigure Printers On SolarisLogin as root Enable Printer Queue Yes Accept Print Jobs Yes Close the admintool windowPost Installation Tasks Installing VolServ Checkpointing -5journaling -5linter -14recovery Update -17volserv -6,1-11Directory -4Linter Database Recovery -6start Changelicense -13,3-17CPU IDAdmintool Administrator userid -6hostname -6license string -6,1-11Bin -4command.config -14config -5console.config Stop