ADIC Version 5.0 manual Check Pointing, Database, Journal

Page 57

Installing VolServ

Step 2. Enter the time in the scr_unix.bsl script for “Everyday” and “CWEEKDAY.”

Step 3. When you are finished editing, restart the Linter Database and backup process by running the following:

#/etc/rc2.d/S90linter

This backup script includes the following two device paths that were set up during the database installation:

ARCDEVICE—stores weekly backups.

LHBDEVICE —stores daily backups.

Check Pointing the

A checkpoint is a snapshot of the database. Taking regular

Database

checkpoints makes recovery of the database faster and more

 

reliable.

 

A checkpoint directory was created outside the database

 

directory during the installation process.

 

 

 

 

Caution

 

 

 

 

 

Make sure this directory is on a separate disk from the VolServ

 

 

Database.

 

 

 

 

Journal the

Journaling of the database was also established during VolServ

Database

installation.

 

 

 

Caution

 

 

 

 

 

Make sure this directory is on a separate disk from the VolServ

 

 

Database.

 

 

 

 

Post Installation Tasks

601351 Rev A

Post Installation Tasks

3-5

Image 57
Contents VolServ Version September Rev a Installing VolServEast Peakview Ave Englewood, CO 80111 USA Phone FAX Trademark NoticeQuestion Circle One Reader Comment FormPage Terms Definitions Software License Premise of This LicenseUse Copying Transfer Rights Price PaymentADIC’s Warranty Ownership & ProtectionProtections Installation Acceptance Installation & AcceptanceUse & Training ResponsibilityWarranty & Servicing WarrantyWarranty Servicing Infringement Indemnification MaintenanceTermination Adic Correspon- dence Disclaimer Limitation LiabilityGeneral Entirety Contents Post Installation Tasks Preface Preface This Book PurposeWho Should Read This Book How This Book is OrganizedConventions used throughout the VolServ technical books ConventionsAre listed below Convention ExampleOnline Books BooksPublications RelatedContact Publications Department Secured Web Site Publications described in the table below are createdStarted Topic Refer To RoadmapPrior to InstallationTasks below are presented as guidelines only since Actual steps for your specific site are uniqueVolServ Directory Structure Directory ContentsMost cases, changes made to the *.config Information Needed Default Customer Entry System Parameters ChecklistName Description Path Permissions Create VolServ DirectoriesEnvironment ConfigureWhere Option DescriptionUsernamepassworduidgidinformationlogindirectoryloginshell Run the passwd command to initialize the vsadm password Change the /etc/shadow file access mode toObtain VolServ License Strings On Sun, use the following commandInstalling VolServ Installation Procedures Installation Procedures Distribution Media Running Installation ScriptInstalling VolServ Installation Summary Following steps are required for a successful installationStep Task Refer to Extract Files from CD Depends on platforms and media type To start extracting the VolServ files, pressInstall VolServ Tip VolServ creates the volserv subdirectory Root directoryInstalling VolServ Parameters Checklist on Installing VolServ Example below, a Scsi library is being installed VolServ database Linter is installed under $VSDIR/linter Procedures Either accept the default path or enter a new pathname Procedures Installing VolServ Post Installation Tasks Post Installation Tasks Put Linter Post Installation TopicsStart and Stop Linter As the root user, run startlinter to startTo edit the Linter backup script, follow the steps below Back Up the Database LocationClose all Linter Database processes by running shutlinter Check Pointing DatabaseJournal Management Database RecoveryModifying Cshrc File Site-Specific TopicsAdditional tasks include the following topics Cycle vsadm to pick up the changesSGI/IRIX Host Configuring Scsi Device NodesHere is an example of the report from hinv Solaris Host Edit the /kernel/drv/sgen.conf file as shown Below Access an OK prompt by simultaneously pressingThis file to support Adic Media Changers libraries Stop key and the a key from a terminalForce re-configuration of hardware devices. This will Reboot the Solaris host machine using boot -r toAt the OK prompt, enter boot to reboot the system Create the device node required for the attachedConfiguring for FileServ Changing Configuration FileChange to the $VSDIR/config subdirectory Config File Description Edit the appropriate *.config filesTasks Servers.config Label Printers ConfiguringOn Solaris Configure PrintersLogin as root Close the admintool window Enable Printer Queue Yes Accept Print Jobs YesPost Installation Tasks Installing VolServ Update -17volserv -6,1-11 Checkpointing -5journaling -5linter -14recoveryDirectory -4Linter Database Recovery -6start Changelicense -13,3-17CPU IDAdministrator userid -6hostname -6license string -6,1-11 AdmintoolBin -4command.config -14config -5console.config Stop