B&B Electronics EIR608-xSFP manual Hardware Installation, Installation Steps

Page 23

Hardware Installation

Installation Steps

1.Unpack the Industrial switch.

2.Ensure the DIN-Rail is tightly screwed to the Industrial switch. If not, refer to DIN-Rail Mounting section for DIN-Rail installation. To panel mount the Industrial switch, refer to Panel Mounting section.

3.Apply power to the switch (refer to the Wiring the Power Inputs section). The power LED will light.

4.Connect CAT 5 cables to the Industrial switch’s RJ-45 ports and to the network devices.

[NOTE] If the network devices do not support MID/MDIX, a crossover cable may be required.

Manual Documentation Number: EIR608-xSFP_0708m

15

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 23

Contents Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Introduction Overview¾ Gvrp FeaturesManual Documentation Number EIR608-xSFP0708m Packing List Front Panel Dimensions W x D x HTop View Wiring the Power Inputs LED Indicators Wiring the Fault Alarm Contact„ RJ-45 Pin Assignments Pin Number Pin MDI-X Signal Name MDI Signal NamePorts Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module DIN-Rail Mounting Mounting InstallationPanel Mounting Installation Steps Hardware InstallationRing Application Dual Homing Application Coupling Ring ApplicationPin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Login in the Console Interface CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelCommands Set List System Commands Set High IP PasswordUsername Low IPPort Commands Set 101001000auto PortidFull half Value Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumber Group NamePortNumbers GroupNameSeconds Spanning Tree Commands Set~61440 Stp-path-cost Spanning-treeHello-time seconds Forward-time secondsTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set Read View Name Write View Name Notify View NameNoAuthNoPrivAuthNoP RivAuthPriv ExactPrifixView Name SNMPV3 agent Port Mirroring Commands SetRemove specified Mibview tableWords 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set SystemlogSMTPBoth ClientserverbothAccount Index Email addressStart time End time Sntp Commands SetTimezone Ring Commands SetMinute Dual Homing Port 1st Ring Port 2nd RingCoupling Port Control PortPreparing for Web Management System LoginAbout Web-based Management Main interface System Information IP ConfigurationDhcp Client Entries Dhcp Server System configurationDhcp Server Port and IP Bindings Tftp Update FirmwareTftp Server IP Address Enter the Tftp server IP Tftp Restore ConfigurationTftp Backup Configuration System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Local Time Zone Conversion from UTC Time at 1200 UTC Sntp ConfigurationManual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingRemove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan configurationVlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q ConfigurationVlan group name and Vlan ID can be changed Click Apply Rapid Spanning Tree Rstp System ConfigurationRstp Port Configuration Snmp Configuration „ Community Strings System ConfigurationContext Table Trap ConfigurationSNMPV3 Configuration User Profile „ Authentication Password Enter passwordSnmp V3 configuration interface MIBview Table Access TableGroup Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority COS ConfigurationTOS Configuration Igmp ConfigurationRing Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time Security 802.1X/Radius Configuration802.1x Port Configuration Misc Configuration „ Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses Factory DefaultSystem Reboot Save ConfigurationTrouble shooting MAC address StandardProtocol Transfer RateConsumption Install „ LC Single mode 9/125um Back-planePower Supply PowerRelay Alarm SafetyStability testing