B&B Electronics EIR608-xSFP manual State Activity

Page 72

State Activity

After setting up the LACP aggregator, port state activity can be configured. Mark the port and click Apply . The port state activity will change to Active or Passive depending on its previous state.

Active: The port automatically sends LACP protocol packets.

Passive: The port responds only if it receives LACP protocol packets from the opposite device.

Note	1.	A link having either two active LACP ports or one active port can
		perform dynamic LACP trunk.
	2.	A link, which has two passive LACP ports, will not perform dynamic
		LACP trunk because both ports are waiting for an LACP protocol
		packet from the opposite device.

Port Trunk – State Activity interface

64	Manual Documentation Number: EIR608-xSFP_0708m
	Manual Documentation Number: EIR608-xSFP_0708m
	B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com
	B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 72

Contents Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Overview IntroductionFeatures ¾ GvrpManual Documentation Number EIR608-xSFP0708m Packing List Dimensions W x D x H Front PanelTop View Wiring the Power Inputs Wiring the Fault Alarm Contact LED IndicatorsPin MDI-X Signal Name MDI Signal Name Ports„ RJ-45 Pin Assignments Pin Number Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module Mounting Installation DIN-Rail MountingPanel Mounting Hardware Installation Installation StepsRing Application Coupling Ring Application Dual Homing ApplicationConnecting to the Console Port DB9 Connector RJ-45 ConnectorPin Assignment Login in the Console Interface CLI Management Commands Level Modes Access Prompt Exit About This Mode1 MethodCommands Set List System Commands Set Password UsernameLow IP High IPPort Commands Set Portid Full half101001000auto Enable Disable ValueTrunk Commands Set Vlan Commands Set GroupIDGroup Name PortNumbersGroupName PortNumberSpanning Tree Commands Set ~61440Seconds Spanning-tree Hello-time secondsForward-time seconds Stp-path-costAutoTrueFalse TrueFalseQOS Commands Set Igmp Commands SetMac / Filter Table Commands Set Snmp Commands Set Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify ViewPort Mirroring Commands Set Remove specifiedMibview table View Name SNMPV3 agent802.1x Commands Set Port IDWords Disable reject accept SecNumber Tftp Commands Set SystemLog, Smtp and Event Commands SetAuthorize Clientserverboth AccountIndex Email address SystemlogSMTPBothSntp Commands Set Start time End timeRing Commands Set MinuteTimezone 1st Ring Port 2nd Ring Coupling PortControl Port Dual Homing PortSystem Login About Web-based ManagementPreparing for Web Management Main interface IP Configuration System InformationDhcp Server System configuration Dhcp Client EntriesTftp Update Firmware Dhcp Server Port and IP BindingsTftp Restore Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Sntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTCManual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkRemove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Vlan configuration Port-based VlanVlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan 802.1Q Configuration „ Hybrid Link Both Access Link and Trunk LinkVlan group name and Vlan ID can be changed Click Apply Rstp System Configuration Rapid Spanning TreeRstp Port Configuration Snmp Configuration System Configuration „ Community StringsTrap Configuration SNMPV3 ConfigurationContext Table „ Authentication Password Enter password User ProfileSnmp V3 configuration interface Access Table Group TableMIBview Table QoS Configuration QoS Policy and Priority TypeCOS Configuration Port Base PriorityIgmp Configuration TOS ConfigurationRing Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time 802.1X/Radius Configuration Security802.1x Port Configuration Misc Configuration MAC Address Table „ Add the Static MAC AddressMAC Filtering Factory Default All MAC AddressesSave Configuration System RebootTrouble shooting Standard ProtocolTransfer Rate MAC address„ LC Single mode 9/125um Back-plane Power SupplyPower Consumption InstallSafety Stability testingRelay Alarm