B&B Electronics EIR608-xSFP manual Trap Configuration, SNMPV3 Configuration, Context Table

Page 85

Trap Configuration

A trap manager is a management station that receives traps (the system alerts generated by the switch). If the trap manager is not defined, traps will not be issued. Create a trap manager by entering the IP address of the station and a community string.

1.IP Address: Enter the IP address of the trap manager.

2.Community: Enter the community string.

3.Trap Version: Select the SNMP trap version type (v1 or v2c).

4.Click Add .

5.To remove the community string, select the community string and click Remove . You cannot edit the name of the default community string.

Trap Managers interface

SNMPV3 Configuration

Context Table

Configure SNMP v3 context table. Assign the context name of context table.

Click Add to add context name. Click context name.

Remove to remove an unwanted

Manual Documentation Number: EIR608-xSFP_0708m

77

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445www.bb-europe.com

Image 85
Contents Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Introduction Overview¾ Gvrp FeaturesManual Documentation Number EIR608-xSFP0708m Packing List Front Panel Dimensions W x D x HTop View Wiring the Power Inputs LED Indicators Wiring the Fault Alarm ContactPorts Pin MDI-X Signal Name MDI Signal Name„ RJ-45 Pin Assignments Pin Number Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module DIN-Rail Mounting Mounting InstallationPanel Mounting Installation Steps Hardware InstallationRing Application Dual Homing Application Coupling Ring ApplicationDB9 Connector RJ-45 Connector Connecting to the Console PortPin Assignment Login in the Console Interface CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelCommands Set List System Commands Set Username PasswordLow IP High IPPort Commands Set Full half Portid101001000auto Value Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumbers Group NameGroupName PortNumber~61440 Spanning Tree Commands SetSeconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Port Mirroring Commands SetMibview table View Name SNMPV3 agentPort ID 802.1x Commands SetWords Sec Disable reject acceptNumber SystemLog, Smtp and Event Commands Set Tftp Commands SetAuthorize Account ClientserverbothIndex Email address SystemlogSMTPBothStart time End time Sntp Commands SetMinute Ring Commands SetTimezone Coupling Port 1st Ring Port 2nd RingControl Port Dual Homing PortAbout Web-based Management System LoginPreparing for Web Management Main interface System Information IP ConfigurationDhcp Client Entries Dhcp Server System configurationDhcp Server Port and IP Bindings Tftp Update FirmwareTftp Backup Configuration Tftp Restore ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Local Time Zone Conversion from UTC Time at 1200 UTC Sntp ConfigurationManual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingRemove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan configurationVlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q ConfigurationVlan group name and Vlan ID can be changed Click Apply Rapid Spanning Tree Rstp System ConfigurationRstp Port Configuration Snmp Configuration „ Community Strings System ConfigurationSNMPV3 Configuration Trap ConfigurationContext Table User Profile „ Authentication Password Enter passwordSnmp V3 configuration interface Group Table Access TableMIBview Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority COS ConfigurationTOS Configuration Igmp ConfigurationRing Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time Security 802.1X/Radius Configuration802.1x Port Configuration Misc Configuration „ Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses Factory DefaultSystem Reboot Save ConfigurationTrouble shooting Protocol StandardTransfer Rate MAC addressPower Supply „ LC Single mode 9/125um Back-planePower Consumption InstallStability testing SafetyRelay Alarm