B&B Electronics EIR608-xSFP manual Rapid Spanning Tree, Rstp System Configuration

Page 81

Rapid Spanning Tree

The Rapid Spanning Tree Protocol (RSTP) is an evolution of Spanning Tree Protocol (STP). It provides a faster spanning tree convergence after a topology change. The switch will auto detect a device that is running STP or RSTP protocol.

RSTP - System Configuration

„ RSTP state can be modified. After modification, click Apply .

¾RSTP mode: Enable or disable the RSTP.

¾Priority (0-61440):a value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. If the value changes, the switch must be rebooted. The value must be multiple of 4096.

¾Max Age (6-40): The number of seconds a bridge waits without receiving Spanning-tree Protocol configuration messages before attempting a reconfiguration. Enter a value between 6 through 40

¾Hello Time (1-10): The time that controls when, the switch sends out the BPDU packet to check RSTP status. Enter a value between 1 and 10.

¾Forward Delay Time (4-30):the number of seconds a port waits before changing from its Rapid Spanning Tree Protocol learning and listening state to the forwarding state. Enter a value between 4 and 30.

Note

Follow this rule to configure the MAX Age, Hello Time, and Forward

 

Delay Time.

 

2 x (Forward Delay Time value -1) >= Max Age value >= 2 x (Hello

 

Time value +1)

Manual Documentation Number: EIR608-xSFP_0708m

73

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445www.bb-europe.com

Image 81
Contents Product Description Eight Port Managed Industrial Ethernet Switches FCC Content Pin Assignment About Web-based Management Preparing for Web Management System Event Log Event Configuration Snmp Configuration Introduction Overview¾ Gvrp FeaturesManual Documentation Number EIR608-xSFP0708m Packing List Front Panel Dimensions W x D x HTop View Wiring the Power Inputs LED Indicators Wiring the Fault Alarm ContactPin MDI-X Signal Name MDI Signal Name Ports„ RJ-45 Pin Assignments Pin Number Cabling Transceiver Inserted LC connector to the transceiver Pull out from the SFP module DIN-Rail Mounting Mounting InstallationPanel Mounting Installation Steps Hardware InstallationRing Application Dual Homing Application Coupling Ring ApplicationConnecting to the Console Port DB9 Connector RJ-45 ConnectorPin Assignment Login in the Console Interface CLI Management Modes Access Prompt Exit About This Mode1 Method Commands LevelCommands Set List System Commands Set Username PasswordLow IP High IPPort Commands Set Portid Full half101001000auto Value Enable DisableTrunk Commands Set GroupID Vlan Commands SetPortNumbers Group NameGroupName PortNumberSpanning Tree Commands Set ~61440Seconds Hello-time seconds Spanning-treeForward-time seconds Stp-path-costTrueFalse AutoTrueFalseIgmp Commands Set QOS Commands SetMac / Filter Table Commands Set Snmp Commands Set NoAuthNoPrivAuthNoP RivAuthPriv NameExactPrifix Read View Name Write View Name Notify ViewRemove specified Port Mirroring Commands SetMibview table View Name SNMPV3 agent802.1x Commands Set Port IDWords Disable reject accept SecNumber Tftp Commands Set SystemLog, Smtp and Event Commands SetAuthorize Account ClientserverbothIndex Email address SystemlogSMTPBothStart time End time Sntp Commands SetRing Commands Set MinuteTimezone Coupling Port 1st Ring Port 2nd RingControl Port Dual Homing PortSystem Login About Web-based ManagementPreparing for Web Management Main interface System Information IP ConfigurationDhcp Client Entries Dhcp Server System configurationDhcp Server Port and IP Bindings Tftp Update FirmwareTftp Restore Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Syslog Configuration System Event Log Smtp Configuration System Event Log Event Configuration Fault Relay Alarm Local Time Zone Conversion from UTC Time at 1200 UTC Sntp ConfigurationManual Documentation Number EIR608-xSFP0708m Daylight Saving Offset mins Enter the offset in minutes IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingRemove Aggregator Information State Activity Port Mirroring Rate Limiting Vlan configuration Port-based Vlan Vlan configurationVlan Port Based interface „ The Vlan is displayed Use 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q ConfigurationVlan group name and Vlan ID can be changed Click Apply Rapid Spanning Tree Rstp System ConfigurationRstp Port Configuration Snmp Configuration „ Community Strings System ConfigurationTrap Configuration SNMPV3 ConfigurationContext Table User Profile „ Authentication Password Enter passwordSnmp V3 configuration interface Access Table Group TableMIBview Table QoS Policy and Priority Type QoS ConfigurationPort Base Priority COS ConfigurationTOS Configuration Igmp ConfigurationRing Manual Documentation Number EIR608-xSFP0708m Rstp cannot exist at the same time Security 802.1X/Radius Configuration802.1x Port Configuration Misc Configuration „ Add the Static MAC Address MAC Address TableMAC Filtering All MAC Addresses Factory DefaultSystem Reboot Save ConfigurationTrouble shooting Protocol StandardTransfer Rate MAC addressPower Supply „ LC Single mode 9/125um Back-planePower Consumption InstallSafety Stability testingRelay Alarm