Black Box ET0100A, ET1000A, ET0010A, ET10000A manual Safety Guidelines, Software Requirements

Page 27

2 Installation

Safety Guidelines

The ETEP does not contain any field-replaceable internal parts. Do not remove the unit’s cover for any reason. The cover is to be removed only by authorized Black Box service personnel.

Authorized service personnel should review the following safety information prior to performing service or maintenance procedures on the ETEP.

CAUTION

Disconnect all power cords before servicing.

WARNING

The ETEP contains a lithium battery, which users should not attempt to replace. Battery replacement must be performed by qualified Black Box personnel. Risk of explosion if battery is replaced by an incorrect type. Used batteries should be disposed of according to the manufacturer’s instructions.

CAUTION

Electrostatic discharge (ESD) can damage electronic components and equipment. ESD occurs when electronic components are improperly handled and can result in complete or intermittent failures. Always follow ESD-prevention procedures when removing and replacing components.

Qualified service personnel should use the following guidelines to prevent ESD damage:

•

•

•

Always use an ESD wrist or ankle strap and ensure that it makes skin contact. Connect the equipment end of the strap to an unpainted metal chassis surface. If no wrist strap is available, ground yourself by touching the metal chassis.

Software Requirements

ETEP software is factory installed on the appliance. A backup copy of the software is provided on the ETEP CD. To learn how to reinstall your software or install an update, refer to the user guide for your management software.

ETEP Installation Guide

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents EncrypTight Enforcement Point Etep Installation Guide Page Table of Contents Initial Setup Maintenance Index Assumptions Contacting Black Box Technical SupportPurpose Intended audienceAbout This Document Etep Installation Guide Etep Introduction Multipoint Ethernet Encryption using EncrypTight ManagerET0010A Physical Description Front Panel ConnectorsStatus Indicators Indicator Light State IndicationRear Panel Front Panel Connectors LED IndicatorsET0100A Physical Description Rear Panel ET0100A Front Panel LED IndicatorsET0100A Rear Panel ET1000A Physical DescriptionET1000A Front Panel LED Indicators ET1000A LED IndicatorsET1000A Rear Panel Power Supply #ET10000A Physical Description ET10000A Front Panel ConnectorsET10000A Front Panel LED Indicators ET10000A LED IndicatorsET10000A Rear Panel Etep Hardware Comparison FeaturesEtep Feature Summary Category FeatureCategory SpecificationsET0010A Mechanical and Environmental Specifications SpecificationCategory Specification ET0100A Mechanical and Environmental SpecificationsET1000A Mechanical and Environmental Specifications MIB Support ET10000A Mechanical and Environmental SpecificationsModule Filename Etep MIBsProduct Overview Etep Installation Guide Software Requirements Safety GuidelinesEtep Site Preparation Third party management station softwareSoftware How it’s used Vendor Installation Instructions ET0010A Firewall PortsFirewall ports To install the Etep in a rack Rack Mount InstallationConnect the power supply cable to the rear panel connector To install the Etep on a solid surface Solid Surface InstallationScrew holes for rubber feet installation on bottom of unit To cable the ET0010A Connecting the Cables ET0010AET0010A Cabling Powering On the ET0010AET0100A Standard Cables Installing the ET0100AET0100A Installation Steps Cabling Requirements ET0100AUnpacking the Shipping Carton ET0100A Rack-Mount Installation ET0100ATo cable the ET0100A Connecting the Cables ET0100ATo power on the ET0100A Powering on the ET0100AImproperly seated ET0100A power cable Installing the ET1000AET1000A Port Cabling Supplied by ET1000A Installation StepsCabling Requirements ET1000A ET1000A Standard CablesUnpacking the Shipping Carton ET1000A Rack Mount Installation ET1000AMounting bracket orientation To install the ET1000A in a rackFor Earth Connection Grounding of DC Power Supply ET1000AConnecting the Cables ET1000A For DC Power Supply OnlyET1000A Cabling Powering on the ET1000ATo power on the ET1000A Dual power supplies on the ET1000A rear panelET10000A Installation Steps Installing the ET10000AET10000A Standard Cables Cabling Requirements ET10000AUnpacking the Shipping Carton ET10000A To install the ET10000A in a rack Rack Mount Installation ET10000ATo cable the ET10000A Connecting the Cables ET10000ASafety Guidelines Powering on the ET10000ATo power on the ET10000A Power-Up ProcedureAppliance model Operational code Shutting Down the EtepShutdown operational codes To shut down the Etep from the CLIShutting Down the Etep Installation Etep Installation Guide Overview Logging In Through a Serial LinkTo log in to the CLI via a serial link About the management port IP address, mask and gateway Configuring the Management PortLink speeds on the management port To configure the management portLink speed Duplex mode Auto-negotiate Fixed Speed All ETEPs About auto-negotiationAttribute Description Management port autoneg command descriptionTo set the date and time Setting the Date and TimeModel Available Throughput To add a license from the command lineEntering a Throughput License Etep Throughput SpeedsConfiguration Example Managing the EtepTo view the Etep throughput speed Etep CLI User Guide EncrypTight Manager User Guide What To Do If an Appliance Fails Preventative MaintenanceTo replace a power supply in the ET1000A Obtaining a License for Replacement UnitsReplacing a Power Supply Replacing the ET1000A Power SupplyTo replace a power supply in the ET10000A Replacing the ET10000A Power SupplyPower supply bracket is secured with two screws Tamper Switch and Zeroization RJ-45 Pin DB-9 Pin To recover the Etep following zeroizationCable Pinouts RS-232 Serial Cable ET0010A and ET10000APin RS-232 Serial Cable ET0100A, ET1000A ModelsMaintenance Etep Installation Guide Symptoms and Solutions LED IndicatorsSymptom Explanation and Possible Solution Symptom Explanation and Possible Solutions Error StateTemperature Threshold and Discarded Traffic Error State Symptoms and SolutionsStatus LEDs Illuminated Description Diagnostic Code DisplayStatus Codes ET0010A ET0010A Self-TestsEtep Operational Codes Diagnostic Codes ET0100A, ET1000A and ET10000AET0010A Operational Codes Etep Self-TestsWeee Directive RoHS DirectiveRegulatory Information Emissions SafetyET0010A Regulatory Information ImmunityEuropean Notice ET0100A Regulatory InformationET0100A Cabling ET1000A Regulatory InformationEMI/EMC ET10000A Regulatory Information Normas Oficiales Mexicanas NOM Electrical Safety StatementRegulatory Information Page Index LEDs See also license Black Box Tech Support FREE! Live /7
Related manuals
Manual 48 pages 53.09 Kb Manual 352 pages 21.02 Kb

EncrypTight Enforcement Point (ETEP), ET10000A, ET0100A, ET0010A, ET1000A specifications

The Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are advanced solutions designed for secure data transmission and network management, catering to modern enterprise needs. These tools integrate cutting-edge technologies to enhance connectivity, security, and efficiency within various environments.

The Black Box ET1000A is primarily a high-performance Ethernet over Twisted Pair (EoTP) solution. It enables users to extend Ethernet signals over long distances using existing twisted-pair cabling without sacrificing speed or reliability. With support for speeds up to 100 Mbps, this device is ideal for organizations looking to upgrade their existing infrastructure without extensive rewiring. Key features include plug-and-play installation, which simplifies deployment, and versatile compatibility with both legacy and modern ethernet networks.

The ET0010A model takes connectivity a step further by providing seamless integration with fiber optics. This device supports transmission distances that far exceed traditional copper solutions, making it a perfect fit for larger facilities or multi-building campuses. Its built-in Ethernet switch enhances network efficiency by providing multiple ports for device connectivity, thus facilitating greater data flow.

EncrypTight technology is a notable feature across these Black Box models, offering advanced encryption capabilities to safeguard sensitive data during transmission. With military-grade encryption protocols, EncrypTight ensures that corporate information remains secure from potential eavesdroppers. This technology is essential for businesses operating in regulated industries or that handle confidential customer information.

The ET0100A model combines intelligence with monitoring features to provide users with comprehensive network insights. It boasts built-in diagnostic tools that enable IT professionals to troubleshoot issues quickly and efficiently. Additionally, it features real-time performance monitoring, allowing users to analyze bandwidth usage and optimize network performance accordingly.

In conclusion, the Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are powerful tools that embody the latest in data transmission and network management technologies. With their unique features—including extended connectivity capabilities, robust encryption technologies, and real-time monitoring solutions—these devices cater to the growing demands of businesses seeking to enhance their network infrastructure while ensuring robust security and efficiency. Integrating these tools into any organization’s operations can fundamentally improve both performance and data protection, making them indispensable in today’s digital landscape.
Top Page Image Contents