Black Box EncrypTight Enforcement Point (ETEP), ET1000A, ET0010A, ET0100A About auto-negotiation

Page 59

Configuring the Management Port

Figure 42 Management Port Default Gateway

Elements of Figure 42:

1ETEP

2Router

3Management workstation

About auto-negotiation

The default setting for the ETEP enables auto-negotiation, which negotiates the link speed, duplex setting, and flow control. Use the autoneg command if the device that the ETEP connects to from a particular port does not support auto-negotiation or flow control.

It is important to configure the ETEP and the other device the same way. Both devices should either auto- negotiate or be set manually to the same speed and duplex mode. Having one device set manually and the other auto-negotiate can cause problems that make the link perform slowly. When manually setting the ETEP link speed, configure the speed and duplex mode to match that of the other device.

On the management port, the ETEPs can negotiate to the following link speeds:

Table 21 Link speeds on the management port

Link speed

Duplex mode

Auto-negotiate

Fixed Speed

 

 

All ETEPs

All ETEPs

10 Mbps

Half-duplex

 

 

 

 

10 Mbps

Full-duplex

 

 

 

 

100 Mbps

Half-duplex

 

 

 

 

100 Mbps

Full-duplex

 

 

 

 

To configure the management port:

1At the command prompt, type configure to enter configuration mode.

2At the config> prompt, type management-interface.

3Assigning an IPv4 address to the management port is mandatory. To set the management port IPv4 address, mask, and gateway, type

ETEP Installation Guide

59

Image 59
Contents EncrypTight Enforcement Point Etep Installation Guide Page Table of Contents Initial Setup Maintenance Index Assumptions Contacting Black Box Technical SupportPurpose Intended audienceAbout This Document Etep Installation Guide Etep Introduction Multipoint Ethernet Encryption using EncrypTight ManagerET0010A Physical Description Front Panel ConnectorsRear Panel Status IndicatorsIndicator Light State Indication ET0100A Physical Description Front Panel ConnectorsLED Indicators Rear Panel ET0100A Front Panel LED IndicatorsET0100A Rear Panel ET1000A Physical DescriptionET1000A Front Panel LED Indicators ET1000A LED IndicatorsET1000A Rear Panel Power Supply #ET10000A Physical Description ET10000A Front Panel ConnectorsET10000A Front Panel LED Indicators ET10000A LED IndicatorsET10000A Rear Panel Etep Hardware Comparison FeaturesEtep Feature Summary Category FeatureCategory SpecificationsET0010A Mechanical and Environmental Specifications SpecificationCategory Specification ET0100A Mechanical and Environmental SpecificationsET1000A Mechanical and Environmental Specifications MIB Support ET10000A Mechanical and Environmental SpecificationsModule Filename Etep MIBsProduct Overview Etep Installation Guide Software Requirements Safety GuidelinesSoftware How it’s used Vendor Etep Site PreparationThird party management station software Firewall ports Installation Instructions ET0010AFirewall Ports To install the Etep in a rack Rack Mount InstallationConnect the power supply cable to the rear panel connector To install the Etep on a solid surface Solid Surface InstallationScrew holes for rubber feet installation on bottom of unit To cable the ET0010A Connecting the Cables ET0010AET0010A Cabling Powering On the ET0010AET0100A Standard Cables Installing the ET0100AET0100A Installation Steps Cabling Requirements ET0100AUnpacking the Shipping Carton ET0100A Rack-Mount Installation ET0100ATo cable the ET0100A Connecting the Cables ET0100ATo power on the ET0100A Powering on the ET0100AImproperly seated ET0100A power cable Installing the ET1000AET1000A Port Cabling Supplied by ET1000A Installation StepsCabling Requirements ET1000A ET1000A Standard CablesUnpacking the Shipping Carton ET1000A Rack Mount Installation ET1000AMounting bracket orientation To install the ET1000A in a rackFor Earth Connection Grounding of DC Power Supply ET1000AConnecting the Cables ET1000A For DC Power Supply OnlyET1000A Cabling Powering on the ET1000ATo power on the ET1000A Dual power supplies on the ET1000A rear panelET10000A Installation Steps Installing the ET10000AET10000A Standard Cables Cabling Requirements ET10000AUnpacking the Shipping Carton ET10000A To install the ET10000A in a rack Rack Mount Installation ET10000ATo cable the ET10000A Connecting the Cables ET10000ASafety Guidelines Powering on the ET10000ATo power on the ET10000A Power-Up ProcedureAppliance model Operational code Shutting Down the EtepShutdown operational codes To shut down the Etep from the CLIShutting Down the Etep Installation Etep Installation Guide To log in to the CLI via a serial link OverviewLogging In Through a Serial Link About the management port IP address, mask and gateway Configuring the Management PortLink speeds on the management port To configure the management portLink speed Duplex mode Auto-negotiate Fixed Speed All ETEPs About auto-negotiationAttribute Description Management port autoneg command descriptionTo set the date and time Setting the Date and TimeModel Available Throughput To add a license from the command lineEntering a Throughput License Etep Throughput SpeedsTo view the Etep throughput speed Configuration ExampleManaging the Etep Etep CLI User Guide EncrypTight Manager User Guide What To Do If an Appliance Fails Preventative MaintenanceTo replace a power supply in the ET1000A Obtaining a License for Replacement UnitsReplacing a Power Supply Replacing the ET1000A Power SupplyTo replace a power supply in the ET10000A Replacing the ET10000A Power SupplyPower supply bracket is secured with two screws Tamper Switch and Zeroization RJ-45 Pin DB-9 Pin To recover the Etep following zeroizationCable Pinouts RS-232 Serial Cable ET0010A and ET10000APin RS-232 Serial Cable ET0100A, ET1000A ModelsMaintenance Etep Installation Guide Symptom Explanation and Possible Solution Symptoms and SolutionsLED Indicators Symptom Explanation and Possible Solutions Error StateTemperature Threshold and Discarded Traffic Error State Symptoms and SolutionsStatus LEDs Illuminated Description Diagnostic Code DisplayStatus Codes ET0010A ET0010A Self-TestsEtep Operational Codes Diagnostic Codes ET0100A, ET1000A and ET10000AET0010A Operational Codes Etep Self-TestsRegulatory Information Weee DirectiveRoHS Directive Emissions SafetyET0010A Regulatory Information ImmunityEuropean Notice ET0100A Regulatory InformationET0100A Cabling ET1000A Regulatory InformationEMI/EMC ET10000A Regulatory Information Normas Oficiales Mexicanas NOM Electrical Safety StatementRegulatory Information Page Index LEDs See also license Black Box Tech Support FREE! Live /7
Related manuals
Manual 48 pages 53.09 Kb Manual 352 pages 21.02 Kb

EncrypTight Enforcement Point (ETEP), ET10000A, ET0100A, ET0010A, ET1000A specifications

The Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are advanced solutions designed for secure data transmission and network management, catering to modern enterprise needs. These tools integrate cutting-edge technologies to enhance connectivity, security, and efficiency within various environments.

The Black Box ET1000A is primarily a high-performance Ethernet over Twisted Pair (EoTP) solution. It enables users to extend Ethernet signals over long distances using existing twisted-pair cabling without sacrificing speed or reliability. With support for speeds up to 100 Mbps, this device is ideal for organizations looking to upgrade their existing infrastructure without extensive rewiring. Key features include plug-and-play installation, which simplifies deployment, and versatile compatibility with both legacy and modern ethernet networks.

The ET0010A model takes connectivity a step further by providing seamless integration with fiber optics. This device supports transmission distances that far exceed traditional copper solutions, making it a perfect fit for larger facilities or multi-building campuses. Its built-in Ethernet switch enhances network efficiency by providing multiple ports for device connectivity, thus facilitating greater data flow.

EncrypTight technology is a notable feature across these Black Box models, offering advanced encryption capabilities to safeguard sensitive data during transmission. With military-grade encryption protocols, EncrypTight ensures that corporate information remains secure from potential eavesdroppers. This technology is essential for businesses operating in regulated industries or that handle confidential customer information.

The ET0100A model combines intelligence with monitoring features to provide users with comprehensive network insights. It boasts built-in diagnostic tools that enable IT professionals to troubleshoot issues quickly and efficiently. Additionally, it features real-time performance monitoring, allowing users to analyze bandwidth usage and optimize network performance accordingly.

In conclusion, the Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are powerful tools that embody the latest in data transmission and network management technologies. With their unique features—including extended connectivity capabilities, robust encryption technologies, and real-time monitoring solutions—these devices cater to the growing demands of businesses seeking to enhance their network infrastructure while ensuring robust security and efficiency. Integrating these tools into any organization’s operations can fundamentally improve both performance and data protection, making them indispensable in today’s digital landscape.