Black Box ET0010A Installing the ET0100A, Cabling Requirements ET0100A, ET0100A Standard Cables

Page 36

Installation

When the appliance powers up, all LEDs illuminate. The power LED remains lit until the unit is powered off.

During the boot process the ETEP cycles through its startup tests, and the corresponding status LEDs are illuminated. After the tests execute successfully, the status indicators turn off.

NOTE

During the boot process the ETEP discards all traffic on its data ports. Once the appliance is operational, the default mode of operation passes all packets in the clear until you deploy security policies.

Installing the ET0100A

To prepare the ET0100A for installation, review the installation steps in Table 14, unpack the shipping carton, and prepare a space for the installation of the appliance.

The steps to perform for a typical installation are listed below.

Table 14

ET0100A Installation Steps

 

 

 

 

 

Step

 

Action to Perform

Description

1

 

Review the cabling requirements.

on page 36

2

 

Unpack the shipping package.

on page 37

3

 

Prepare a space for installation of the ET0100A.

on page 37

4

 

Connect the cables.

on page 38

5

 

Apply power to the ET0100A.

on page 39

 

 

 

 

Cabling Requirements: ET0100A

Table 15 outlines the standard cables used with each port on the ET0100A. The connector type listed indicates only what is required to connect to the ET0100A port, and may or may not be the same connector type required for the other end of the cable. Some cables are supplied by Black Box and others are user-supplied.

Table 15

ET0100A Standard Cables

 

 

 

 

ET0100A Port

Cabling

Supplied by...

Power receptacle

Power supply cable certified

Black Box

 

 

and approved for use in the

 

 

 

country of interest

 

RS-232 Port

Shielded copper null modem

Black Box

 

 

cable, RS-232 DB9 connector

 

 

 

(female to male)

 

10/100 Ethernet Management

Shielded Category 5 straight

Black Box

Port

 

through cable (STP), RJ-45

 

 

 

connectora

 

36

ETEP Installation Guide

Image 36
Contents EncrypTight Enforcement Point Etep Installation Guide Page Table of Contents Initial Setup Maintenance Index Contacting Black Box Technical Support PurposeIntended audience AssumptionsAbout This Document Etep Installation Guide Multipoint Ethernet Encryption using EncrypTight Manager Etep IntroductionFront Panel Connectors ET0010A Physical DescriptionStatus Indicators Indicator Light State IndicationRear Panel Front Panel Connectors LED IndicatorsET0100A Physical Description ET0100A Front Panel LED Indicators Rear PanelET1000A Physical Description ET0100A Rear PanelET1000A LED Indicators ET1000A Front Panel LED IndicatorsPower Supply # ET1000A Rear PanelET10000A Front Panel Connectors ET10000A Physical DescriptionET10000A LED Indicators ET10000A Front Panel LED IndicatorsET10000A Rear Panel Features Etep Feature SummaryCategory Feature Etep Hardware ComparisonSpecifications ET0010A Mechanical and Environmental SpecificationsSpecification CategoryET0100A Mechanical and Environmental Specifications Category SpecificationET1000A Mechanical and Environmental Specifications ET10000A Mechanical and Environmental Specifications MIB SupportEtep MIBs Module FilenameProduct Overview Etep Installation Guide Safety Guidelines Software RequirementsEtep Site Preparation Third party management station softwareSoftware How it’s used Vendor Installation Instructions ET0010A Firewall PortsFirewall ports Rack Mount Installation To install the Etep in a rackConnect the power supply cable to the rear panel connector Solid Surface Installation To install the Etep on a solid surfaceScrew holes for rubber feet installation on bottom of unit Connecting the Cables ET0010A To cable the ET0010APowering On the ET0010A ET0010A CablingInstalling the ET0100A ET0100A Installation StepsCabling Requirements ET0100A ET0100A Standard CablesRack-Mount Installation ET0100A Unpacking the Shipping Carton ET0100AConnecting the Cables ET0100A To cable the ET0100APowering on the ET0100A To power on the ET0100AInstalling the ET1000A Improperly seated ET0100A power cableET1000A Installation Steps Cabling Requirements ET1000AET1000A Standard Cables ET1000A Port Cabling Supplied byRack Mount Installation ET1000A Unpacking the Shipping Carton ET1000ATo install the ET1000A in a rack Mounting bracket orientationGrounding of DC Power Supply ET1000A Connecting the Cables ET1000AFor DC Power Supply Only For Earth ConnectionPowering on the ET1000A ET1000A CablingDual power supplies on the ET1000A rear panel To power on the ET1000AInstalling the ET10000A ET10000A Installation StepsCabling Requirements ET10000A ET10000A Standard CablesUnpacking the Shipping Carton ET10000A Rack Mount Installation ET10000A To install the ET10000A in a rackConnecting the Cables ET10000A To cable the ET10000APowering on the ET10000A Safety GuidelinesPower-Up Procedure To power on the ET10000AShutting Down the Etep Shutdown operational codesTo shut down the Etep from the CLI Appliance model Operational codeShutting Down the Etep Installation Etep Installation Guide Overview Logging In Through a Serial LinkTo log in to the CLI via a serial link Configuring the Management Port About the management port IP address, mask and gatewayTo configure the management port Link speed Duplex mode Auto-negotiate Fixed Speed All ETEPsAbout auto-negotiation Link speeds on the management portManagement port autoneg command description Attribute DescriptionSetting the Date and Time To set the date and timeTo add a license from the command line Entering a Throughput LicenseEtep Throughput Speeds Model Available ThroughputConfiguration Example Managing the EtepTo view the Etep throughput speed Etep CLI User Guide EncrypTight Manager User Guide Preventative Maintenance What To Do If an Appliance FailsObtaining a License for Replacement Units Replacing a Power SupplyReplacing the ET1000A Power Supply To replace a power supply in the ET1000AReplacing the ET10000A Power Supply To replace a power supply in the ET10000APower supply bracket is secured with two screws Tamper Switch and Zeroization To recover the Etep following zeroization Cable PinoutsRS-232 Serial Cable ET0010A and ET10000A RJ-45 Pin DB-9 PinRS-232 Serial Cable ET0100A, ET1000A Models PinMaintenance Etep Installation Guide Symptoms and Solutions LED IndicatorsSymptom Explanation and Possible Solution Error State Temperature Threshold and Discarded TrafficError State Symptoms and Solutions Symptom Explanation and Possible SolutionsDiagnostic Code Display Status Codes ET0010AET0010A Self-Tests Status LEDs Illuminated DescriptionDiagnostic Codes ET0100A, ET1000A and ET10000A ET0010A Operational CodesEtep Self-Tests Etep Operational CodesWeee Directive RoHS DirectiveRegulatory Information Safety ET0010A Regulatory InformationImmunity EmissionsET0100A Regulatory Information European NoticeET1000A Regulatory Information ET0100A CablingEMI/EMC Normas Oficiales Mexicanas NOM Electrical Safety Statement ET10000A Regulatory InformationRegulatory Information Page Index LEDs See also license Black Box Tech Support FREE! Live /7
Related manuals
Manual 48 pages 53.09 Kb Manual 352 pages 21.02 Kb

EncrypTight Enforcement Point (ETEP), ET10000A, ET0100A, ET0010A, ET1000A specifications

The Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are advanced solutions designed for secure data transmission and network management, catering to modern enterprise needs. These tools integrate cutting-edge technologies to enhance connectivity, security, and efficiency within various environments.

The Black Box ET1000A is primarily a high-performance Ethernet over Twisted Pair (EoTP) solution. It enables users to extend Ethernet signals over long distances using existing twisted-pair cabling without sacrificing speed or reliability. With support for speeds up to 100 Mbps, this device is ideal for organizations looking to upgrade their existing infrastructure without extensive rewiring. Key features include plug-and-play installation, which simplifies deployment, and versatile compatibility with both legacy and modern ethernet networks.

The ET0010A model takes connectivity a step further by providing seamless integration with fiber optics. This device supports transmission distances that far exceed traditional copper solutions, making it a perfect fit for larger facilities or multi-building campuses. Its built-in Ethernet switch enhances network efficiency by providing multiple ports for device connectivity, thus facilitating greater data flow.

EncrypTight technology is a notable feature across these Black Box models, offering advanced encryption capabilities to safeguard sensitive data during transmission. With military-grade encryption protocols, EncrypTight ensures that corporate information remains secure from potential eavesdroppers. This technology is essential for businesses operating in regulated industries or that handle confidential customer information.

The ET0100A model combines intelligence with monitoring features to provide users with comprehensive network insights. It boasts built-in diagnostic tools that enable IT professionals to troubleshoot issues quickly and efficiently. Additionally, it features real-time performance monitoring, allowing users to analyze bandwidth usage and optimize network performance accordingly.

In conclusion, the Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are powerful tools that embody the latest in data transmission and network management technologies. With their unique features—including extended connectivity capabilities, robust encryption technologies, and real-time monitoring solutions—these devices cater to the growing demands of businesses seeking to enhance their network infrastructure while ensuring robust security and efficiency. Integrating these tools into any organization’s operations can fundamentally improve both performance and data protection, making them indispensable in today’s digital landscape.