Black Box ET1000A manual Unpacking the Shipping Carton ET0100A, Rack-Mount Installation ET0100A

Page 37

 

 

 

 

Installing the ET0100A

 

 

 

 

 

 

Table 15

ET0100A Standard Cables

 

 

 

 

 

 

ET0100A Port

Cabling

Supplied by...

 

Remote and Local ports

Shielded Category 5 straight

User

 

 

 

through cables (STP), RJ-45

 

 

 

 

connectora

 

a.The local, remote, and Ethernet management ports are auto-sensing for polarity. You can use shielded Category 5 straight through cables or crossover cables when connecting to these ports.

NOTE

To meet the requirements of FCC Part 15 and the EU EMC Directive 2004/108/EC, use only shielded cables with the ET0100A (DB-9 null modem cables and Category 5 STP cables).

Unpacking the Shipping Carton: ET0100A

Remove all product components from the shipping carton and compare the contents to the packing list. Keep all packaging in case it is necessary to return the unit.

The ET0100A is packaged with the standard items listed below. Additional cables, country-specific power cords, and other accessories can be ordered separately.

1ET0100A chassis

Firmware and software is factory-installed on the unit.

2Accessory Kit

Rack mount kit containing two mounting brackets and 10 screws

(1) Power cable (US)

(1) Shielded DB-9 null modem cable (female to male)

(1)Shielded Category 5 straight through cable (STP) with RJ-45 connector CD containing user documentation and a backup copy of the ETEP software

Rack-Mount Installation: ET0100A

The ET0100A can be mounted in a standard 19-inch rack using the mounting kit, or simply placed on a rack shelf or solid surface. Before installing the ET0100A in a 19-inch rack, review the rack-mounting guidelines listed in “ETEP Site Preparation” on page 28.

To mount the ETEP in a standard 19-inch equipment rack, have the following tools and materials available:

Two mounting brackets, supplied in the Accessory Kit

(6)small screws and (4) large screws, supplied in the Accessory Kit #1 Phillips and #2 Phillips screwdrivers (user-supplied)

ETEP Installation Guide

37

Image 37
Contents EncrypTight Enforcement Point Etep Installation Guide Page Table of Contents Initial Setup Maintenance Index Purpose Contacting Black Box Technical SupportIntended audience AssumptionsAbout This Document Etep Installation Guide Etep Introduction Multipoint Ethernet Encryption using EncrypTight ManagerET0010A Physical Description Front Panel ConnectorsIndicator Light State Indication Status IndicatorsRear Panel LED Indicators Front Panel ConnectorsET0100A Physical Description Rear Panel ET0100A Front Panel LED IndicatorsET0100A Rear Panel ET1000A Physical DescriptionET1000A Front Panel LED Indicators ET1000A LED IndicatorsET1000A Rear Panel Power Supply #ET10000A Physical Description ET10000A Front Panel ConnectorsET10000A Front Panel LED Indicators ET10000A LED IndicatorsET10000A Rear Panel Etep Feature Summary FeaturesCategory Feature Etep Hardware ComparisonET0010A Mechanical and Environmental Specifications SpecificationsSpecification CategoryCategory Specification ET0100A Mechanical and Environmental SpecificationsET1000A Mechanical and Environmental Specifications MIB Support ET10000A Mechanical and Environmental SpecificationsModule Filename Etep MIBsProduct Overview Etep Installation Guide Software Requirements Safety GuidelinesThird party management station software Etep Site PreparationSoftware How it’s used Vendor Firewall Ports Installation Instructions ET0010AFirewall ports To install the Etep in a rack Rack Mount InstallationConnect the power supply cable to the rear panel connector To install the Etep on a solid surface Solid Surface InstallationScrew holes for rubber feet installation on bottom of unit To cable the ET0010A Connecting the Cables ET0010AET0010A Cabling Powering On the ET0010AET0100A Installation Steps Installing the ET0100ACabling Requirements ET0100A ET0100A Standard CablesUnpacking the Shipping Carton ET0100A Rack-Mount Installation ET0100ATo cable the ET0100A Connecting the Cables ET0100ATo power on the ET0100A Powering on the ET0100AImproperly seated ET0100A power cable Installing the ET1000ACabling Requirements ET1000A ET1000A Installation StepsET1000A Standard Cables ET1000A Port Cabling Supplied byUnpacking the Shipping Carton ET1000A Rack Mount Installation ET1000AMounting bracket orientation To install the ET1000A in a rackConnecting the Cables ET1000A Grounding of DC Power Supply ET1000AFor DC Power Supply Only For Earth ConnectionET1000A Cabling Powering on the ET1000ATo power on the ET1000A Dual power supplies on the ET1000A rear panelET10000A Installation Steps Installing the ET10000AET10000A Standard Cables Cabling Requirements ET10000AUnpacking the Shipping Carton ET10000A To install the ET10000A in a rack Rack Mount Installation ET10000ATo cable the ET10000A Connecting the Cables ET10000ASafety Guidelines Powering on the ET10000ATo power on the ET10000A Power-Up ProcedureShutdown operational codes Shutting Down the EtepTo shut down the Etep from the CLI Appliance model Operational codeShutting Down the Etep Installation Etep Installation Guide Logging In Through a Serial Link OverviewTo log in to the CLI via a serial link About the management port IP address, mask and gateway Configuring the Management PortLink speed Duplex mode Auto-negotiate Fixed Speed All ETEPs To configure the management portAbout auto-negotiation Link speeds on the management portAttribute Description Management port autoneg command descriptionTo set the date and time Setting the Date and TimeEntering a Throughput License To add a license from the command lineEtep Throughput Speeds Model Available ThroughputManaging the Etep Configuration ExampleTo view the Etep throughput speed Etep CLI User Guide EncrypTight Manager User Guide What To Do If an Appliance Fails Preventative MaintenanceReplacing a Power Supply Obtaining a License for Replacement UnitsReplacing the ET1000A Power Supply To replace a power supply in the ET1000ATo replace a power supply in the ET10000A Replacing the ET10000A Power SupplyPower supply bracket is secured with two screws Tamper Switch and Zeroization Cable Pinouts To recover the Etep following zeroizationRS-232 Serial Cable ET0010A and ET10000A RJ-45 Pin DB-9 PinPin RS-232 Serial Cable ET0100A, ET1000A ModelsMaintenance Etep Installation Guide LED Indicators Symptoms and SolutionsSymptom Explanation and Possible Solution Temperature Threshold and Discarded Traffic Error StateError State Symptoms and Solutions Symptom Explanation and Possible SolutionsStatus Codes ET0010A Diagnostic Code DisplayET0010A Self-Tests Status LEDs Illuminated DescriptionET0010A Operational Codes Diagnostic Codes ET0100A, ET1000A and ET10000AEtep Self-Tests Etep Operational CodesRoHS Directive Weee DirectiveRegulatory Information ET0010A Regulatory Information SafetyImmunity EmissionsEuropean Notice ET0100A Regulatory InformationET0100A Cabling ET1000A Regulatory InformationEMI/EMC ET10000A Regulatory Information Normas Oficiales Mexicanas NOM Electrical Safety StatementRegulatory Information Page Index LEDs See also license Black Box Tech Support FREE! Live /7
Related manuals
Manual 48 pages 53.09 Kb Manual 352 pages 21.02 Kb

EncrypTight Enforcement Point (ETEP), ET10000A, ET0100A, ET0010A, ET1000A specifications

The Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are advanced solutions designed for secure data transmission and network management, catering to modern enterprise needs. These tools integrate cutting-edge technologies to enhance connectivity, security, and efficiency within various environments.

The Black Box ET1000A is primarily a high-performance Ethernet over Twisted Pair (EoTP) solution. It enables users to extend Ethernet signals over long distances using existing twisted-pair cabling without sacrificing speed or reliability. With support for speeds up to 100 Mbps, this device is ideal for organizations looking to upgrade their existing infrastructure without extensive rewiring. Key features include plug-and-play installation, which simplifies deployment, and versatile compatibility with both legacy and modern ethernet networks.

The ET0010A model takes connectivity a step further by providing seamless integration with fiber optics. This device supports transmission distances that far exceed traditional copper solutions, making it a perfect fit for larger facilities or multi-building campuses. Its built-in Ethernet switch enhances network efficiency by providing multiple ports for device connectivity, thus facilitating greater data flow.

EncrypTight technology is a notable feature across these Black Box models, offering advanced encryption capabilities to safeguard sensitive data during transmission. With military-grade encryption protocols, EncrypTight ensures that corporate information remains secure from potential eavesdroppers. This technology is essential for businesses operating in regulated industries or that handle confidential customer information.

The ET0100A model combines intelligence with monitoring features to provide users with comprehensive network insights. It boasts built-in diagnostic tools that enable IT professionals to troubleshoot issues quickly and efficiently. Additionally, it features real-time performance monitoring, allowing users to analyze bandwidth usage and optimize network performance accordingly.

In conclusion, the Black Box ET1000A, ET0010A, EncrypTight, and ET0100A are powerful tools that embody the latest in data transmission and network management technologies. With their unique features—including extended connectivity capabilities, robust encryption technologies, and real-time monitoring solutions—these devices cater to the growing demands of businesses seeking to enhance their network infrastructure while ensuring robust security and efficiency. Integrating these tools into any organization’s operations can fundamentally improve both performance and data protection, making them indispensable in today’s digital landscape.