Cisco Systems AIRONET 1000 manual Safety Information, FCC Safety Compliance Statement

Page 22

Chapter 2 Installing the Access Point

Safety Information

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point.

FCC Safety Compliance Statement

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

General Safety Guidelines

Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

Warnings

Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245B

Warning In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332

Warning This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353

Warning Read the installation instructions before you connect the system to its power source. Statement 1004

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

2-2

OL-9403-04

 

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Americas Headquarters Page N T E N T S Troubleshooting Declarations of Conformity and Regulatory Information B-1 OL-9403-04 Audience PrefacePurpose Organization Conventions ViiiPreface Conventions Related Publications Finding the Product Serial Number Xii Overview Guidelines for Using the Access Points Hardware Features2illustrates the left side connectors on the access point Single or Dual-Radio Operation Ethernet Port UL 2043 Certification Network Configuration Example Typical Layer 3 Access Point Network Configuration ExampleTypical Layer 2 Access Point Network Configuration Example Installing the Access Point FCC Safety Compliance Statement Safety InformationGeneral Safety Guidelines Basic Installation Guidelines Unpacking the Access PointPackage Contents Before Beginning the Installation Mounting the Access Point in the Correct DirectionAccess Point Layout and Connectors 3illustrates the right side of the access point4illustrates the access point LEDs on the top of the unit Controller Discovery ProcessDeploying the Access Points on the Wireless Network Review the Mounting Overview section onMounting Overview Factory-Supplied Mounting Options Mounting Access Points Using a Ceiling-Mount Base Attaching the Access Point and Ceiling-Mount BaseMounting Access Points Using the Ceiling-Mount Clips Attaching the Ceiling-Mount Clips to the Access Point135674 10 Attaching the Mounting Screws to the Access Point 135671 Mounting the Access Point Using the Flush-Mount Bracket 12 Attaching the Access Point to the Flush-Mount Bracket Securing the Access Point Using a Security Cable Connecting the Ethernet and Power Cables13 Ethernet and Power Ports Powering Up the Access Point Connecting to an Ethernet Network with Local PowerReturning MAC Information Troubleshooting Using Dhcp Option Checking the Access Point LEDs Power LED Alarm LED Low Power Condition OL-9403-04 Translated Safety Warnings OL-9403-04 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementAIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9 EMC Declaration of Conformity for RF Exposure Japanese Translation Access Points with Ieee 802.11a Radios Chinese Translation English TranslationAll Access Points Declaration of Conformity Statements OL-9403-04 Page OL-9403-04 Access Point Specifications Specifications Category 802.11b 802.11g 802.11aPower output settings CCK Vcci OL-9403-04 Power output settings CCK Vcci OL-9403-04 Channels and Power Levels OL-9403-04 Priming Access Points Prior to Deployment Figure E-1 Typical Priming ConfigurationAppendix E Priming Access Points Prior to Deployment Appendix E Priming Access Points Prior to Deployment OL-9403-04 Configuring Dhcp Option Access Point Vendor Class Identifier VCI OverviewConfiguring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value D E IN-2 IN-3 IN-4

AIRONET 1000 specifications

Cisco Systems AIRONET 1000 is a robust wireless access point designed to meet the demands of modern networking environments. This product is particularly beneficial for small to medium-sized businesses seeking to enhance their wireless connectivity while ensuring reliability and security.

One of the standout features of the AIRONET 1000 is its dual-band functionality, operating effectively on both the 2.4 GHz and 5 GHz bands. This capability allows for greater flexibility and improved performance, as users can connect to the least congested frequency for their specific needs. Additionally, the access point supports multiple-input and multiple-output (MIMO) technology, which improves signal quality and enhances data rates by utilizing multiple antennas to transmit and receive data simultaneously.

The AIRONET 1000 is equipped with Cisco's CleanAir technology, providing powerful interference management. This innovation automatically identifies and mitigates sources of wireless interference, ensuring a more stable and consistent connection. Security is another critical aspect of this access point; it includes advanced features such as Wi-Fi Protected Access (WPA), which safeguards network data through encryption protocols, thus protecting sensitive information from unauthorized access.

Furthermore, the Cisco Systems AIRONET 1000 integrates seamlessly with Cisco’s DNA software, allowing for advanced networking capabilities such as network automation, analytics, and security policy enforcement. The access point also supports Power over Ethernet (PoE), simplifying installation by enabling power and data connectivity through a single cable, reducing clutter while enhancing deployment flexibility.

With its lightweight design and compact form factor, the AIRONET 1000 is easy to install and can be placed in various locations, ensuring optimal coverage across an area. Whether in an office, retail space, or educational institution, this access point is built to deliver high-performance wireless connectivity.

In conclusion, the Cisco Systems AIRONET 1000 combines advanced wireless technologies, security features, and ease of deployment, making it a highly effective solution for any organization looking to improve its wireless network infrastructure. Its ability to handle current demands while being scalable for future growth reflects Cisco's commitment to providing reliable and efficient networking results.
Top Page Image Contents