Cisco Systems AIRONET 1000 manual For Home or Office USE

Page 50

Appendix B Declarations of Conformity and Regulatory Information

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Manufacturers Federal Communication Commission Declaration of Conformity Statement

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

Model:

AIR-AP1010-A-K9 / AIR-AP1020-A-K9 / AIR-AP1030-A-K9

AIR-AP1010-B-K9 / AIR-AP1020-B-K9 / AIR-AP1030-B-K9

FCC Certification number:

LDK102057

Manufacturer:

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

This device complies with Part 15 rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

•Reorient or relocate the receiving antenna.

•Increase separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician.

Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

 

B-2

OL-9403-04

 

 

 

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Americas Headquarters Page N T E N T S Troubleshooting Declarations of Conformity and Regulatory Information B-1 OL-9403-04 Purpose Organization PrefaceAudience Conventions ViiiPreface Conventions Related Publications Finding the Product Serial Number Xii Overview Guidelines for Using the Access Points Hardware Features2illustrates the left side connectors on the access point Single or Dual-Radio Operation Ethernet Port UL 2043 Certification Network Configuration Example Typical Layer 3 Access Point Network Configuration ExampleTypical Layer 2 Access Point Network Configuration Example Installing the Access Point General Safety Guidelines Safety InformationFCC Safety Compliance Statement Package Contents Unpacking the Access PointBasic Installation Guidelines Before Beginning the Installation Mounting the Access Point in the Correct DirectionAccess Point Layout and Connectors 3illustrates the right side of the access point4illustrates the access point LEDs on the top of the unit Controller Discovery ProcessDeploying the Access Points on the Wireless Network Review the Mounting Overview section onMounting Overview Factory-Supplied Mounting Options Mounting Access Points Using a Ceiling-Mount Base Attaching the Access Point and Ceiling-Mount BaseMounting Access Points Using the Ceiling-Mount Clips Attaching the Ceiling-Mount Clips to the Access Point135674 10 Attaching the Mounting Screws to the Access Point 135671 Mounting the Access Point Using the Flush-Mount Bracket 12 Attaching the Access Point to the Flush-Mount Bracket Securing the Access Point Using a Security Cable Connecting the Ethernet and Power Cables13 Ethernet and Power Ports Powering Up the Access Point Connecting to an Ethernet Network with Local PowerReturning MAC Information Troubleshooting Using Dhcp Option Checking the Access Point LEDs Power LED Alarm LED Low Power Condition OL-9403-04 Translated Safety Warnings OL-9403-04 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Industry Canada Canadian Compliance StatementAIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9 EMC Declaration of Conformity for RF Exposure Japanese Translation Access Points with Ieee 802.11a Radios Chinese Translation English TranslationAll Access Points Declaration of Conformity Statements OL-9403-04 Page OL-9403-04 Access Point Specifications Specifications Category 802.11b 802.11g 802.11aPower output settings CCK Vcci OL-9403-04 Power output settings CCK Vcci OL-9403-04 Channels and Power Levels OL-9403-04 Priming Access Points Prior to Deployment Figure E-1 Typical Priming ConfigurationAppendix E Priming Access Points Prior to Deployment Appendix E Priming Access Points Prior to Deployment OL-9403-04 Configuring Dhcp Option Access Point Vendor Class Identifier VCI OverviewConfiguring Option 43 for 1000 Series Access Points Quotation marks must be includedType + Length + Value D E IN-2 IN-3 IN-4

AIRONET 1000 specifications

Cisco Systems AIRONET 1000 is a robust wireless access point designed to meet the demands of modern networking environments. This product is particularly beneficial for small to medium-sized businesses seeking to enhance their wireless connectivity while ensuring reliability and security.

One of the standout features of the AIRONET 1000 is its dual-band functionality, operating effectively on both the 2.4 GHz and 5 GHz bands. This capability allows for greater flexibility and improved performance, as users can connect to the least congested frequency for their specific needs. Additionally, the access point supports multiple-input and multiple-output (MIMO) technology, which improves signal quality and enhances data rates by utilizing multiple antennas to transmit and receive data simultaneously.

The AIRONET 1000 is equipped with Cisco's CleanAir technology, providing powerful interference management. This innovation automatically identifies and mitigates sources of wireless interference, ensuring a more stable and consistent connection. Security is another critical aspect of this access point; it includes advanced features such as Wi-Fi Protected Access (WPA), which safeguards network data through encryption protocols, thus protecting sensitive information from unauthorized access.

Furthermore, the Cisco Systems AIRONET 1000 integrates seamlessly with Cisco’s DNA software, allowing for advanced networking capabilities such as network automation, analytics, and security policy enforcement. The access point also supports Power over Ethernet (PoE), simplifying installation by enabling power and data connectivity through a single cable, reducing clutter while enhancing deployment flexibility.

With its lightweight design and compact form factor, the AIRONET 1000 is easy to install and can be placed in various locations, ensuring optimal coverage across an area. Whether in an office, retail space, or educational institution, this access point is built to deliver high-performance wireless connectivity.

In conclusion, the Cisco Systems AIRONET 1000 combines advanced wireless technologies, security features, and ease of deployment, making it a highly effective solution for any organization looking to improve its wireless network infrastructure. Its ability to handle current demands while being scalable for future growth reflects Cisco's commitment to providing reliable and efficient networking results.
Top Page Image Contents