Cisco Systems AIRONET 1000 manual Powering Up the Access Point

Page 39

Chapter 2 Installing the Access Point

Powering Up the Access Point

Connecting to an Ethernet Network with Local Power

Note If your access point is connected to in-line power, do not connect the power module to the access point.

Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source:

Step 1 Connect a Category 5 Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see Figure 2-13).

Step 2 Plug the other end of the Ethernet cable into an non-powered Ethernet port on your 10/100 Ethernet LAN.

Step 3 Connect the power module output connector to the access point’s 48-VDC power port (see Figure 2-13). Step 4 Plug the power module power cord into an approved 100- to 240-VAC outlet.

Powering Up the Access Point

After you power up the access point, it begins a power-up sequence that you can check by observing the access point LEDs. The red Alarm LED turns on for about 15 to 20 seconds and then all LEDs blink sequentially back and forth, indicating that the access point is trying to find a controller. Refer to “Checking the Access Point LEDs” section on page 3-3for LED descriptions.

After the access point finds the controller, the access point downloads new operating system code if the access point code version differs from the controller code version. During the download process, all access point LEDs blink simultaneously. When the operating system download is successful, the access point reboots.

Normal operation is indicated when the Alarm LED is off, the Power LED is green, and the 2.4 GHz and 5 GHz LEDs are blinking to indicate radio activity.

If no LEDs are on, the access point might not be receiving sufficient power.

If all the LEDs blink sequentially for more than five minutes, the access point is unable to find its primary, secondary, or tertiary controllers. Check the connection between the access point and its controllers and ensure they are on the same subnet or that the access point has a route back to its primary, secondary, and tertiary controllers. If the access point is not on the same subnet as the controllers, ensure there is a properly configured DHCP server on the same subnet as the access point. See the “Using DHCP Option 43” section on page 3-2for DHCP information.

Note To allow client roaming between access points, the access points must be on the same subnet.

Note Connect only one power source to the access point, for example: When using in-line power, do not connect the power module to the access point.

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

 

OL-9403-04

2-19

 

 

 

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Americas Headquarters Page N T E N T S Troubleshooting Declarations of Conformity and Regulatory Information B-1 OL-9403-04 Preface AudiencePurpose Organization Viii ConventionsPreface Conventions Related Publications Finding the Product Serial Number Xii Overview Hardware Features Guidelines for Using the Access Points2illustrates the left side connectors on the access point Single or Dual-Radio Operation Ethernet Port UL 2043 Certification Typical Layer 3 Access Point Network Configuration Example Network Configuration ExampleTypical Layer 2 Access Point Network Configuration Example Installing the Access Point Safety Information FCC Safety Compliance StatementGeneral Safety Guidelines Unpacking the Access Point Basic Installation GuidelinesPackage Contents Mounting the Access Point in the Correct Direction Before Beginning the Installation3illustrates the right side of the access point Access Point Layout and ConnectorsController Discovery Process 4illustrates the access point LEDs on the top of the unitReview the Mounting Overview section on Deploying the Access Points on the Wireless NetworkMounting Overview Factory-Supplied Mounting Options Attaching the Access Point and Ceiling-Mount Base Mounting Access Points Using a Ceiling-Mount BaseAttaching the Ceiling-Mount Clips to the Access Point Mounting Access Points Using the Ceiling-Mount Clips135674 10 Attaching the Mounting Screws to the Access Point 135671 Mounting the Access Point Using the Flush-Mount Bracket 12 Attaching the Access Point to the Flush-Mount Bracket Connecting the Ethernet and Power Cables Securing the Access Point Using a Security Cable13 Ethernet and Power Ports Connecting to an Ethernet Network with Local Power Powering Up the Access PointReturning MAC Information Troubleshooting Using Dhcp Option Checking the Access Point LEDs Power LED Alarm LED Low Power Condition OL-9403-04 Translated Safety Warnings OL-9403-04 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Canadian Compliance Statement Industry CanadaAIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9 EMC Declaration of Conformity for RF Exposure Japanese Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Declaration of Conformity Statements OL-9403-04 Page OL-9403-04 Specifications Category 802.11b 802.11g 802.11a Access Point SpecificationsPower output settings CCK Vcci OL-9403-04 Power output settings CCK Vcci OL-9403-04 Channels and Power Levels OL-9403-04 Figure E-1 Typical Priming Configuration Priming Access Points Prior to DeploymentAppendix E Priming Access Points Prior to Deployment Appendix E Priming Access Points Prior to Deployment OL-9403-04 Configuring Dhcp Option Overview Access Point Vendor Class Identifier VCIQuotation marks must be included Configuring Option 43 for 1000 Series Access PointsType + Length + Value D E IN-2 IN-3 IN-4

AIRONET 1000 specifications

Cisco Systems AIRONET 1000 is a robust wireless access point designed to meet the demands of modern networking environments. This product is particularly beneficial for small to medium-sized businesses seeking to enhance their wireless connectivity while ensuring reliability and security.

One of the standout features of the AIRONET 1000 is its dual-band functionality, operating effectively on both the 2.4 GHz and 5 GHz bands. This capability allows for greater flexibility and improved performance, as users can connect to the least congested frequency for their specific needs. Additionally, the access point supports multiple-input and multiple-output (MIMO) technology, which improves signal quality and enhances data rates by utilizing multiple antennas to transmit and receive data simultaneously.

The AIRONET 1000 is equipped with Cisco's CleanAir technology, providing powerful interference management. This innovation automatically identifies and mitigates sources of wireless interference, ensuring a more stable and consistent connection. Security is another critical aspect of this access point; it includes advanced features such as Wi-Fi Protected Access (WPA), which safeguards network data through encryption protocols, thus protecting sensitive information from unauthorized access.

Furthermore, the Cisco Systems AIRONET 1000 integrates seamlessly with Cisco’s DNA software, allowing for advanced networking capabilities such as network automation, analytics, and security policy enforcement. The access point also supports Power over Ethernet (PoE), simplifying installation by enabling power and data connectivity through a single cable, reducing clutter while enhancing deployment flexibility.

With its lightweight design and compact form factor, the AIRONET 1000 is easy to install and can be placed in various locations, ensuring optimal coverage across an area. Whether in an office, retail space, or educational institution, this access point is built to deliver high-performance wireless connectivity.

In conclusion, the Cisco Systems AIRONET 1000 combines advanced wireless technologies, security features, and ease of deployment, making it a highly effective solution for any organization looking to improve its wireless network infrastructure. Its ability to handle current demands while being scalable for future growth reflects Cisco's commitment to providing reliable and efficient networking results.
Top Page Image Contents