Cisco Systems AIRONET 1000 manual Deploying the Access Points on the Wireless Network

Page 27

Chapter 2 Installing the Access Point

Deploying the Access Points on the Wireless Network

•DHCP server discovery—Uses DHCP Option 43 to provide controller IP addresses to the access points. Cisco switches support a DHCP server option. For additional information, refer to the “Configuring DHCP Option 43” section on page F-1.

•DNS server discovery—The access point uses the name CISCO-LWAPP-CONTROLLER.<local domain> to discover the controller IP addresses from a DNS server. Where <local domain> is the access point domain name.

Cisco recommends that you configure a DHCP server with Option 43 to provide the controller IP addresses to your access points. Cisco switches provide a DHCP server option that is typically used for this purpose.

Deploying the Access Points on the Wireless Network

Prior to beginning the actual access point deployment, perform these tasks:

•Ensure a site survey has been preformed.

•Ensure your network infrastructure devices are operational and properly configured.

•Ensure your controllers are connected to switch trunk ports.

•Ensure your switch is configured with untagged access ports for connecting your access points.

•Ensure a DHCP server with Option 43 configured is reachable by your access points.

•Review the “Mounting Overview” section on page 2-8.

To deploy your access points, follow these steps:

Step 1 Obtain the access point location map created during your building site survey.

Step 2 Review the access point locations and identify the specific mounting methods required for each access point location.

Step 3 For each access point perform these steps:

a.Record the access point MAC address on the access point location map (see the “Returning MAC Information” section on page 2-20).

b.Mount the access point at the indicated destination using the specified mounting method. For specific mounting instructions, see these sections:

–Horizontal surface, such as a ceiling (see the Mounting Access Points Using a Ceiling-Mount Base, page 2-10).

–Below a suspended ceiling (see the “Mounting Access Points Using the Ceiling-Mount Clips” section on page 2-11).

–Perpendicular to a vertical surface, such as a wall (see the “Mounting the Access Point Using a Projection Wall Mount Bracket” section on page 2-13).

–Parallel to a vertical surface, such as a wall ( see the “Mounting the Access Point Using the Flush-Mount Bracket” section on page 2-15).

c.Optionally secure the access point using a security cable (see the “Securing the Access Point Using a Security Cable” section on page 2-17).

d.Connect the access point cables (Ethernet, optional power, optional antennas). For instructions see the “Connecting the Ethernet and Power Cables” section on page 2-17.

Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide

 

OL-9403-04

2-7

 

 

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Americas Headquarters Page N T E N T S Troubleshooting Declarations of Conformity and Regulatory Information B-1 OL-9403-04 Preface AudiencePurpose Organization Viii ConventionsPreface Conventions Related Publications Finding the Product Serial Number Xii Overview Hardware Features Guidelines for Using the Access Points2illustrates the left side connectors on the access point Single or Dual-Radio Operation Ethernet Port UL 2043 Certification Typical Layer 3 Access Point Network Configuration Example Network Configuration ExampleTypical Layer 2 Access Point Network Configuration Example Installing the Access Point Safety Information FCC Safety Compliance StatementGeneral Safety Guidelines Unpacking the Access Point Basic Installation GuidelinesPackage Contents Mounting the Access Point in the Correct Direction Before Beginning the Installation3illustrates the right side of the access point Access Point Layout and ConnectorsController Discovery Process 4illustrates the access point LEDs on the top of the unitReview the Mounting Overview section on Deploying the Access Points on the Wireless NetworkMounting Overview Factory-Supplied Mounting Options Attaching the Access Point and Ceiling-Mount Base Mounting Access Points Using a Ceiling-Mount BaseAttaching the Ceiling-Mount Clips to the Access Point Mounting Access Points Using the Ceiling-Mount Clips135674 10 Attaching the Mounting Screws to the Access Point 135671 Mounting the Access Point Using the Flush-Mount Bracket 12 Attaching the Access Point to the Flush-Mount Bracket Connecting the Ethernet and Power Cables Securing the Access Point Using a Security Cable13 Ethernet and Power Ports Connecting to an Ethernet Network with Local Power Powering Up the Access PointReturning MAC Information Troubleshooting Using Dhcp Option Checking the Access Point LEDs Power LED Alarm LED Low Power Condition OL-9403-04 Translated Safety Warnings OL-9403-04 Declarations of Conformity and Regulatory Information For Home or Office USE Vcci Statement for Japan Canadian Compliance Statement Industry CanadaAIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9 EMC Declaration of Conformity for RF Exposure Japanese Translation Chinese Translation English Translation Access Points with Ieee 802.11a RadiosAll Access Points Declaration of Conformity Statements OL-9403-04 Page OL-9403-04 Specifications Category 802.11b 802.11g 802.11a Access Point SpecificationsPower output settings CCK Vcci OL-9403-04 Power output settings CCK Vcci OL-9403-04 Channels and Power Levels OL-9403-04 Figure E-1 Typical Priming Configuration Priming Access Points Prior to DeploymentAppendix E Priming Access Points Prior to Deployment Appendix E Priming Access Points Prior to Deployment OL-9403-04 Configuring Dhcp Option Overview Access Point Vendor Class Identifier VCIQuotation marks must be included Configuring Option 43 for 1000 Series Access PointsType + Length + Value D E IN-2 IN-3 IN-4

AIRONET 1000 specifications

Cisco Systems AIRONET 1000 is a robust wireless access point designed to meet the demands of modern networking environments. This product is particularly beneficial for small to medium-sized businesses seeking to enhance their wireless connectivity while ensuring reliability and security.

One of the standout features of the AIRONET 1000 is its dual-band functionality, operating effectively on both the 2.4 GHz and 5 GHz bands. This capability allows for greater flexibility and improved performance, as users can connect to the least congested frequency for their specific needs. Additionally, the access point supports multiple-input and multiple-output (MIMO) technology, which improves signal quality and enhances data rates by utilizing multiple antennas to transmit and receive data simultaneously.

The AIRONET 1000 is equipped with Cisco's CleanAir technology, providing powerful interference management. This innovation automatically identifies and mitigates sources of wireless interference, ensuring a more stable and consistent connection. Security is another critical aspect of this access point; it includes advanced features such as Wi-Fi Protected Access (WPA), which safeguards network data through encryption protocols, thus protecting sensitive information from unauthorized access.

Furthermore, the Cisco Systems AIRONET 1000 integrates seamlessly with Cisco’s DNA software, allowing for advanced networking capabilities such as network automation, analytics, and security policy enforcement. The access point also supports Power over Ethernet (PoE), simplifying installation by enabling power and data connectivity through a single cable, reducing clutter while enhancing deployment flexibility.

With its lightweight design and compact form factor, the AIRONET 1000 is easy to install and can be placed in various locations, ensuring optimal coverage across an area. Whether in an office, retail space, or educational institution, this access point is built to deliver high-performance wireless connectivity.

In conclusion, the Cisco Systems AIRONET 1000 combines advanced wireless technologies, security features, and ease of deployment, making it a highly effective solution for any organization looking to improve its wireless network infrastructure. Its ability to handle current demands while being scalable for future growth reflects Cisco's commitment to providing reliable and efficient networking results.
Top Page Image Contents