Ricoh FW770 manual Clear/Stop key

Page 16

11.{Function Select} key

Press to change which setting you are ed- iting. The current selection is shown by the indicators above the key:

•Paper Length

•Leading Edge

•Copy Counter

Also used for copying a selected portion of the original.

12.{+} and {—}key

Press to increase the value being edited. Press to decrease the value being edited.

13.Leading Edge/Copy Counter in- dicator

Displays the margin settings and the number of copies made.

14.Roll Feeder indicator

Light up when you select Roll Feeder 1 or 2.

15.{RF Select/Cut} key

Use to select the paper feed type (when the Roll Feeder option is installed). Also press to stop a copy job.

16.{Copy Media} key

Press to select the type of copy paper you are using.

The copier will apply more or less heat accordingly.

•The top indicator-Translucent paper indicator

•The bottom indicator-Film indicator

17.{Emergency Stop} key

Press to stop the copying process imme- diately.

Use if your original is getting stuck in the copier.

If you stop operation by pressing this key, remove both the original and paper.

18.Density indicator and {i}, {j}keys

Shows the density level the copies will have.

Press the left key to make copies lighter. Press the right key to make copies darker.

19.{Paper Feed}key

Press to feed the paper.

Paper Feed indicator(LED) lights up when the machine is ready to feed roll paper.

20.{Clear/Stop} key

When entering numbers, press to cancel. While copying, press to stop copying.

4

Image 16

Contents FW770 Overseas Affiliates ⇒ P.75 Power Connection Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turn On the Main Power Turning on the PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Handling TonerToner Storage Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Changing The Roll Paper Size Setting the Roll Paper HolderRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder Others Absolutely nothing happensIf Jams Occur Frequently If Copies Look WrongCopies Come Out Dog Eared CreasesBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex

Related manuals

Manual 6 pages 5.13 Kb