Ricoh FW770 manual

Page 6

RWARNING:

•Connect the power cord directly into a wall outlet and never use an extension cord.

•Only connect the machine to the power source described on the inside front cover of this man- ual.

•Avoid multi-wiring.

•Do not damage, break or make any modifications to the power cord. Do not place heavy ob- jects on it, pull it hard or bend it more than necessary. These actions could cause an electric shock or fire.

•Do not plug or unplug the power cord with your hands wet. Otherwise, an electric shock might occur.

•Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug be- comes frayed or otherwise damaged.

•Make sure the wall outlet is near the machine and freely accessible so that in event of an emer- gency it can be unplugged easily.

•Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following conditions exists:

•You spill something into the equipment.

•You suspect that your equipment needs service or repair.

•Your equipment's cover has been damaged.

•Do not take apart or attempt any modifications to this machine. There is a risk of fire, electric shock, explosion or loss of sight. If the machine has laser systems, there is a risk of serious eye damage.

•To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or screws other than those specified in this manual.

•Some parts of the machine are at a high voltage and could give you an electric shock. Also, if the machine has laser systems, direct (or indirect) reflected eye contact with the laser beam may cause serious eye damage. When the machine needs to be checked, adjusted, or repaired, contact your service representative.

•Do not keep using the machine with a fault or defect. Contact your service representative.

•If the machine looks damaged or breaks down, smoke is coming out, there is a strange smell or anything looks unusual, immediately turn off the operation and main power switches then unplug the power cord from the wall. Do not continue using the machine in this condition.

Contact your service representative.

•Do not put any metal objects or containers holding water (e.g. vases, flowerpots, glasses) on the machine. If the contents fall inside the machine, a fire or electric shock could occur.

•Do not incinerate spilled toner or used toner. Toner dust might ignite when exposed to an open flame.

•Disposal can take place at our authorized dealer or at appropriate collection sites.

•Dispose of the used toner cartridge in accordance with the local regulation.

ii

Page 5 Page 7
Image 6
Page 5 Page 7
Contents FW770 Overseas Affiliates ⇒ P.75 Power Connection Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Storage TonerHandling Toner Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Jams Occur Frequently OthersAbsolutely nothing happens If Copies Look WrongCreases Copies Come Out Dog EaredBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex
Related manuals
Manual 6 pages 5.13 Kb
Top Page Image Contents