Ricoh FW770 manual Partial Copying

Page 44

Copy Settings

Partial Copying

The Partial Copy function copies only a part of an original.

You need to enter start and end points in the feed direction of the original .

3

Note

❒You cannot use the Partial Copying function when using the Rear Table.

❒You cannot use the Partial Copying function for originals shorter than 150mm.

❒You can use the Partial Copying function for originals longer than 1270mm.

❒If you set the start point within 130 mm of the leading edge of the original, the copier will regard the leading edge as the start point.

❒The minimum available space between the start point and the end point is 30 mm.

❒If you do not set the end point after setting the start point (a), the copier will regard the trailing edge of the original as the end point (b).

❒If you do not set the end point in the Semi Synchro Cutting function, the pa- per extend by 200mm from the end point (from c to d). The paper extend by 310mm from the trailing edge.

A Hold down the {Function Select} key for three seconds or more.

A "P" will blink in the copy counter display.

32

Image 44

Contents FW770 Overseas Affiliates ⇒ P.75 Power Connection Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turn Off the Main Power Turning on the PowerTurn On the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Handling TonerToner Storage Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Removing the Roll Paper Holder Setting the Roll Paper HolderChanging The Roll Paper Size Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder Others Absolutely nothing happensIf Jams Occur Frequently If Copies Look WrongBlack streaks appear on copies CreasesCopies Come Out Dog Eared Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex

Related manuals

Manual 6 pages 5.13 Kb