Ricoh FW770 manual Operation Panel, Function indicators

Page 15

Operation Panel

1.Function indicators

These indicators show which setting you are currently editing, Press the Function key to cycle through them.

•The top indicator (Paper Length indi- cator) lights when the paper length is being set.

•The middle indicator (Leading Edge indicator) lights when the leading margin is being set.

•The bottom indicator (Copy Counter indicator) lights when the number of copies is being set.

2.Paper Length display

Shows the length of paper the Roll Feeder will send.

3.{Preset Cut} key

Press to scrolls through the preset paper lengths for the Roll Feeder.

4.{Cut Select} key

Turns Semi synchro Cut or Preset/Varia- ble Cut on and off.

5.Energy Saver indicator

Shows that the machine is in a state of wait (Energy Saver). Press key 9.

6.Troubleshooting indicators

⇒P.61 “Troubleshooting” for details.

7.Wait indicator

Shows that the copier is not yet ready to copy.

8.Ready (d), Set Original(R), Set Paper (K), Bypass Select (a) indica- tor.

When Ready indicator lights up, you can set paper.The Set Paper indicator on the left lights, and then Bypass Select indica- tor goes on.

9.{Clear Modes/Energy Saver} key

Cancels all of current settings. When you hold down this key for three seconds or more, the copier enters the Energy Saver mode allowing you to conserve power.

To exit Energy Saver mode, press this key again.

10.{Program} key

Allows you to recall or set a program. The program indicator(LED) lights after you store the setting.

3

Image 15

Contents FW770 Overseas Affiliates ⇒ P.75 Power Connection Means Power on Means Stand by Safety During Operation Safety InformationPage Iii Energy Star Program SpecificationSymbols How to Read this ManualTable of Contents Specifications Viii Copier Exterior Guide to ComponentsMain switch Operation Panel Function indicatorsClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power Recommended Originals ⇒ P.17 Using the Rear TableNon-recommended Originals Recommended Paper Anti-humidity Heater Used Toner TonerHandling Toner Toner StorageBasic Copying Copying to sheets CopyingMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Semi Synchro cutting Copying onto Roll Paper OptionPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Variable Cutting Press the Preset Cut keyYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copying Onto Other Media Copy SettingsAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking Copier starts copying P will disappear Program key Programming Settings You Often UseRecalling Settings Stored in the Program key Changing the Default SettingTurn off the main switch Press the Function Select key User ToolsUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Changing The Used Toner Bottle Maintaining Your CopierMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Something Goes Wrong If Indicator Lights UpIf the Original is Jammed at the Exit If Jams OccurIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Copies Look Wrong OthersAbsolutely nothing happens If Jams Occur FrequentlyCreases Copies Come Out Dog EaredBlack streaks appear on copies Clean the Exposure Glass & the Platen Plate Daily MaintenanceDos & Donts Machine Environment Where to Put Your CopierPower Connection Access To Machine Copier SpecificationsRoll feeder OptionsIndex

Related manuals

Manual 6 pages 5.13 Kb