Ricoh FW770 manual This value can be changed to 1, 2, 3, or 10 intervals

Page 54

Copy Settings

•Auto Energy Saver Mode(+10): The fusing unit needs to be hot for copying. When the copier is idle, the fusing unit can be kept hot to save time or it can

be allowed to cool to save energy. This feature can be set to start automatical- ly, but you can also turn it on yourself by pressing and holding the {Clear Modes/Energy Saver} key for three seconds.

Note

❒0: None, 1: Yes

❒Default: 0

❒The machine can not enter the energy saving mode if toner end indicator

 

lights.

3

• Screen Message Setting(+11): When the copier is idle, the copy counter can

 

 

be made to display a message. There are five possible messages: "Pre_heat",

 

"Sleeping", "0123456789", “Have a good day", and "Hello I love you". This fea-

 

ture can also be turned off.

 

Note

 

❒ 0: None, 1: "Pre_heat", 2: "Hello I love you", 3: "0123456789", 4: "Sleeping" ,

 

5: Have a good day".

 

• Leading Edge Increase/Decrease Adjustment Preliminary Interval(+12):

 

When changing a function setting (margin, multiple copies, or paper length)

 

by holding down the {+} or {− } key, the setting will change by a preset value.

 

This value can be changed to 1, 2, 3, or 10 intervals.

 

Note

 

❒ 0: 3 intervals, 1: 1 interval, 2: 2 intervals, 3: 10 intervals

 

❒ Default: 0

 

• Auto Off Time(+15): You can set the time the machine waits after the last op-

 

eration before switching itself off automatically. The time can be set by

 

minute from 1 to 240 minutes.

 

Note

 

❒ Default: 30min

 

❒ Auto Off cannot be used in the following cases.

 

• When the Wait indicator goes on

 

• When the toner end indicator goes on

 

• When the front door is open

 

• While copying

 

• When a paper misfeed occurs or SC call appears

 

• The machine cannot enter the Auto Off mode if the roll end indicator

 

lights while copying repeatedly.

42

Page 53 Page 55
Image 54
Page 53 Page 55
Contents FW770 Overseas Affiliates ⇒ P.75 Power Connection Means Power on Means Stand by Safety Information Safety During OperationPage Iii Specification Energy Star ProgramHow to Read this Manual SymbolsTable of Contents Specifications Viii Guide to Components Copier ExteriorMain switch Function indicators Operation PanelClear/Stop key Turning on the Power Turn On the Main PowerTurn Off the Main Power ⇒ P.17 Using the Rear Table Recommended OriginalsNon-recommended Originals Recommended Paper Anti-humidity Heater Toner Storage TonerHandling Toner Used TonerCopying Basic Copying Copying to sheetsMake sure that the Bypass Tray is selected Basic Copying Copying to sheets Copying Using the Roll Feeder Option Copying Using the Rear Table Copying Copying onto Roll Paper Option Semi Synchro cuttingPress the Cut Select key1 Copying onto Roll Paper Option Preset Cutting Press the Preset Cut key Variable CuttingYou can change the settings by 1mm 0.1 steps Using The Roll Cutting Rail Option Copying Copy Settings Copying Onto Other MediaAdjusting the Fusing Temperature Manually Adjusting Copy Image Density Making Several Copies of the Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copyPartial Copying P will stay on, not blinking Copier starts copying P will disappear Programming Settings You Often Use Program keyChanging the Default Setting Recalling Settings Stored in the Program keyTurn off the main switch User Tools Press the Function Select keyUser Tools Settings You Can Change with User Tools Settings You Can Change with User Tools This value can be changed to 1, 2, 3, or 10 intervals Semi-synchro Cut Length Adjustment+19 Adjust the cut length Standard Density 1 Darker Image Density Default Maintaining Your Copier Changing The Used Toner BottleMaintaining Your Copier Close the upper unit Adding Toner Adding Toner Close the toner cartridge cover and the original table Adding Toner Setting the Roll Paper Holder Changing The Roll Paper SizeRemoving the Roll Paper Holder Changing The Roll Paper Size Loading a Roll Of Paper Insert the paper roll as far as it will go Maintaining Your Copier Hold the paper B , and then slide the cutter a Close the Roll Feeder Loading a New Roll Onto Paper Cutting Rail Option Maintaining Your Copier If Indicator Lights Up If Something Goes WrongIf Jams Occur If the Original is Jammed at the ExitIf Sheet Paper is Jammed in the Feed-in Slot If Sheet Paper is Jammed at the Paper Exit If Roll Paper Jams Troubleshooting If You Cannot See the Roll Paper Jam Hold the paper B , and then slide the cutter a Close the Roll Feeder If Jams Occur Frequently OthersAbsolutely nothing happens If Copies Look WrongCreases Copies Come Out Dog EaredBlack streaks appear on copies Daily Maintenance Clean the Exposure Glass & the Platen PlateDos & Donts Where to Put Your Copier Machine EnvironmentPower Connection Access To Machine Specifications CopierOptions Roll feederIndex
Related manuals
Manual 6 pages 5.13 Kb
Top Page Image Contents