Samsung Network Printer manual IP address setup, Using SetIP, Using SyncThru Web Admin Service

Page 10

IP address setup

Before using your network print server in your network, you must set TCP/IP addresses for the print server. You will need your printer card’s MAC address, IP address, subnet mask, and gateway address. First, check with your network administrator for the TCP/IP addresses.

NOTE: The MAC address is the hardware serial number of the network printer card. You can check the address by printing the Network Printer Configuration Page. For printing the page, refer to your printer user’s guide.

You can set your print server’s IP address via the following methods:

•Printer control panel: If your printer has a control panel and the network configuration menu, you can set the IP address directly from the printer. Refer to your printer user’s guide.

•SetIP program: Go to the Using SetIP.

•SyncThru Web Admin Service: Go to the Using SyncThru Web Admin Service.

•SyncThru Web Service: Once you have set an IP address for your network print server, you can use the embedded web server in the network printer card to change the address. Go to page 2.3.

•DHCP: You can use Dynamic Host Configuration Protocol (DHCP) to get an IP address automatically assigned by your network administrator, if your network system supports this protocol.

•BOOTP: A network-based server using the BootStrap protocol (BOOTP) can notify the network printer card of its assigned IP address each time the printer turns on, if your network system supports this protocol.

NOTE: To get an IP address from the DHCP or BOOTP server, the IP assignment method must be set to DHCP or BOOTP.

Using SetIP

1From the Windows Start menu, select Programs Æ Samsung Network Printer Utilities Æ SetIP Æ SetIP.

The program automatically detects and displays new and configured print servers on your network.

2Select the name of your printer and click . If you

cannot find your printer name, click to refresh the list. Even with this step, if you cannot find your printer name, then contact Network Administrator.

3Enter your network printer card’s MAC address (hardware address), IP address, subnet mask, default gateway, and then click Apply.

4Click OK to confirm the settings.

5Click Exit to close the SetIP program.

Using SyncThru Web Admin Service

1From the Windows Start menu, select Programs Æ Samsung Network Printer Utilities Æ SyncThru Web Admin Service Æ SyncThru Web Admin Service.

The homepage of SyncThru Web Admin Service opens in your default web browser.

2If necessary, change the display language.

2.2

Programs supplied on the Network Utilities CD

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Page Contents Appendix Federal Communications Commission FCC For products fitted with EU-approved radio devicesPlace and the system is fully assembled Introduction Package contentsGetting started Supported network environmentsComputer Requirements Installing your Network Printer CardSystem requirements IBMViewing the SyncThru Web Admin Service User’s Guide Installing softwareUninstalling software Programs supplied on the Network Utilities CDUsing SetIP IP address setupUsing SyncThru Web Admin Service Click Devices Æ Add device Using SyncThru Web ServiceEnter your print server’s TCP/IP addresses and click Apply Using Snmp Configuring DHCP/BOOTPConfiguring Snmp TCP/IP environmentConfiguring Ddns Configuring SLPUsing SLP Dynamic DNS DdnsUsing UPnP Configuring WinsConfiguring UPnP BonjourStandard TCP/IP port Printing protocolsLPR port IPP port Configuring IPP in the print serverSamsung Printer Port Windows 2000/XP/2003Additional functions Click Network Settings Æ General ResetClick Network Settings Æ Reset Ethernet speedNetWare environment Configuring NetWareNetWare printing Adding a printer Printing in NetWareAdding a queue Assignments menuEtherTalk environment Configuring EtherTalkConfiguring the printer EtherTalk printingTCP/IP printing Bonjour printerOverview Wireless network environmentBasic concept and terms WEP encryption Ieee 802.11 authenticationWPA Wi-Fi Protected Access IeeeSelect Network Settings Æ Wireless Before configuring the print serverWireless settings Status DescriptionSecurity Authentication Encryption method Method Mode Wireless basic settings Wireless security settingsNone Open System No encryption Static WEP security mode settings None security mode settingsEnhanced Security mode settings Using EAP-TLS Click ConfigureUsing WPA-PSK Select File Æ Add/Remove Snap-inUsing EAP-TTLS Items Specifications SpecificationsWireless specifications AppendixOpenSSL License OpenSSL StatementsDisclaimer Bootp Ad hoc peer-to-peer mode BonjourDdns Dhcp Http SLP Snmp UPnP Static WEP 6.4 WEP encryption Rev.1.00
Top Page Image Contents