Samsung ML-4551N manual Setting the memory in the PostScript printer properties

Page 61

3Grasp the control board cover and remove it.

4Take out a new DIMM from its plastic bag.

5Locate the extra DMM slot and align the notch on the DIMM with the groove at the DIMM slot, holding the DIMM by its edges.

1

2

1notch

2groove

6Push the DIMM into the printer until it snaps into place. Make sure that the latches fit over the notches located on either side of the DIMM.

7Close the control board cover by aligning the groove on it with the notch on the printer and sliding it.

8Reinstall the duplex-slot cover or the duplex unit.

9Reconnect the power cord and printer cable, and turn the printer on.

Setting the memory in the PostScript printer properties

After installing the DIMM, you need to select it in the printer properties of the PostScript printer driver to enable its use.

1Make sure that the PostScript printer driver is installed on your computer. To install the PostScript printer driver, see the Software Section.

2Click the Windows Start menu.

3For Windows 98/Me/NT 4.0/2000, select Settings and then Printers.

For Windows XP/2003, select Printers and Faxes.

4Select the Samsung ML-4550 Series PS printer.

5Click the right mouse button on the printer icon and select Properties.

6For Windows 98/Me, select the Device Option tab.

For Windows NT 4.0/2000/XP/2003, select the Device Settings tab.

7Select the amount of memory you installed from Printer Memory in the Installable Options section.

For Windows 98, select Installable Options → VMOption → change setting for:NMOption → change memory.

8Click OK.

10.2 <Installing accessories>

Image 61

Contents Page Page Country Customer Care Center Web Site Contact Samsung World WideContents Installing accessories TroubleshootingSpecifications Important Precautions and Safety Information FCC Regulations Canadian Radio Interference RegulationsReplacing the Fitted Plug for UK Only Openssl License Original Ssleay License Introduction Special featuresSoftware Section You can print in Windows 98/Me/NT 4.0/2000/XP/2003 Features ML-4550 ML-4551N ML-4551NDFront view Printer overviewControl panel overview Finding more informationClearance space Selecting a locationUsing control panel menus System setupAccessing control panel menus Job manager menu Menu overviewInformation menu Orientation Layout menuSimplex MarginGraphic menu Paper menuSystem Setup menu PostScript Emulation menuNetwork menu Changing the font setting Using toner save modePrinting a demo Changing the display languageSupplied software Software overviewSystem requirements Printer driver featuresWindows Macintosh LinuxRequirements Via network administration programs Network setupVia the control panel Configuring EtherTalk Configuring TCP/IPDynamic addressing BOOTP/DHCP Supported operating systemsSetting Ethernet speed Configuring IPX frame typesRestoring the network configuration Printing a network configurationSelecting print media Loading print mediaType Size Weight Type Size Dimensions Weighta CapacitybSupported sizes of paper Print media for duplex printingGuidelines for special print media Guidelines for selecting and storing print mediaMedia type Guidelines Loading paper Changing the size of the paper in the tray Using the standard tray or the optional traysLoad the paper with the side to be printed on facing up Using the multi-purpose trayTips on using the multi-purpose tray Using manual feed modePrinting to the output tray Face down Selecting an output locationPrinting to the rear cover Face up Printing a document Canceling a print job Canceling a print jobBasic printing Printing a documentAccessories Ordering supplies and accessoriesHow to purchase Toner cartridgesCleaning the printer MaintenanceCleaning the outside of the printer Cleaning the inside of the printerMaintenance Maintaining the toner cartridge Printing a cleaning sheetToner cartridge storage Expected cartridge yieldRedistributing toner cartridge Checking the remaining tonerReplacing the toner cartridge Maintenance Clearing the Toner Low Replace Toner message Maintenance partsItems Yield Average Clearing paper jams TroubleshootingTray Paper feed areaOptional tray Multi-purpose tray Around the toner cartridgeDuplex unit area Paper exit areaDuplex jam Condition Suggested solutions Troubleshooting checklistTips for avoiding paper jams Understanding display messages Understanding the status LEDLow Heat Error Message Meaning Suggested solutions LoadLSU Motor Error OPC is CleaningToner cartridge-related messages Solving general printing problems Spool Settings button Settings and Printers. RightClick the Samsung ML-4550 Series PCL 6 printer iconSolving print quality problems Condition Suggested solutions Curl or wave Condition Suggested solutions VerticalRepetitive Defects Common PostScript problems Common Windows problemsCommon Macintosh problems Common Linux problemsInstallable Options section to InstalledPrecautions when installing accessories Installing accessoriesInstalling a dual in-line memory module Dimm Disconnect the power cordSelect the Samsung ML-4550 Series PS printer Setting the memory in the PostScript printer propertiesRemoving a Dimm Installing a network interface cardInstalling the hard disk Using the hard diskSetting the hard disk in the printer properties Printing with the optional hard disk Setting the time and dateStoring a job Printing a stored jobControlling the active job queue Printing using the form filesTo delete a file from the queue To promote a file from the queuePrinter specifications SpecificationsSpecifications and Description ECP Index System requirements Linux 3.3 Macintosh 3.3 Windows Software section Contents Using Windows Postscript Driver Using Your Printer in Linux Installing Software for Local Printing Installing Printer SoftwareTypical Installation Select Typical installation for a local printer. Click NextCustom Installation Select the components to be installed and click Next Select Custom installation. Click NextInstalling Software for Network Printing Custom Installation Installing Printer Software in Windows Changing the Software Language Reinstalling Printer SoftwareNext Removing Printer SoftwareSelect your printer driver from the Name drop-down list Printing a DocumentLayout Tab Printer SettingsPaper Orientation Source Paper TabScaling Printing Toner Save Mode ResolutionGraphics Tab Advanced OptionsOn the Job Setting Job SettingExtras Tab Using Help Using a Favorite SettingAbout Tab Printer TabPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersPrinting a Reduced or Enlarged Document Printing on Both Sides of PaperFitting Your Document to a Selected Paper Size NoneUsing an Existing Watermark Using WatermarksCreating a Watermark Editing a WatermarkWhat is an Overlay? Using OverlaysUsing a Page Overlay Creating a New Page OverlayAdvanced Using Windows PostScript DriverUsing the right-click menu Using the shortcut iconOverview Direct Print Utility PrintingSetting Up a Client Computer Setting Up a Host ComputerCheck the Share this printer box Select Local Port and click New PortPrinter Setting Troubleshooting GuideUnderstanding Smart Panel Toner LevelChanging the Smart Panel Program Settings Opening the Troubleshooting GuideUsing Printer Settings Utility Using Onscreen Help FileInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Click Uninstall Uninstalling the Unified Linux DriverPrinters Configuration Using the Unified Driver ConfiguratorOpening the Unified Driver Configurator Double-clickUnified Driver Configurator on the desktopPorts Configuration Configuring Printer PropertiesClasses Tab Printing Files Printing from ApplicationsFile menu Click Continue Installing Software for MacintoshFor a Network-connected Macintosh Setting Up the PrinterFor a USB-connected Macintosh Mac OS 8.6 ~Layout Setting Changing Printer SettingsPrinting a Document ResolutionQuality Printer Features SettingPrinting Multiple Pages on One Sheet of Paper Reverse DuplexDuplex Printing Index Resolution Macintosh 36 Windows GGGGGGGGGGGGGRev.2.00