Panasonic DMR-E85H manual Television operation, Point the remote control at the television

Page 11

Television operation

You can configure the remote control TV operation buttons to turn the television on/off, change the television input mode, select the television channel and change the television volume.

Point the remote control at the television

While pressing [Í TV], enter the code with the numbered buttons.

e.g., 01:	[0] ➡ [1]
Manufacturer and Code No.

	Brand	Code
Panasonic/National		01, 02, 03, 04

GOLDSTAR/LG		15, 16
HITACHI		08

JVC		07
MITSUBISHI		09, 10

NEC		13
PHILIPS		12

SAMSUNG		12, 17, 18
SANYO		14, 19

SHARP		11
SONY		05

TOSHIBA		06

Test by turning on the television and changing channels. Repeat the procedure until you find the code that allows correct operation. ≥If your television brand is not listed or if the code listed for your television does not allow control of your television, this remote

control is not compatible with your television.

When other Panasonic products respond to this remote control

If other Panasonic products are placed close together, change the remote control code on the main unit and the remote control (the two must match).

Under normal circumstances use the factory set code “DVD 1”.

1 While stopped

Press [FUNCTIONS].

2 Press [3, 4, 2, 1] to select “SETUP” and press [ENTER].

3 Press [3, 4] to select “Others” and press [1].

4 Press [3, 4] to select “Remote

Control” and press [ENTER].

5 Press [3, 4] to select the code (“DVD 1”, “DVD 2” or “DVD 3”) and press [ENTER].

SETUP	Remote Control

	Press “±” and “ENTER” together
Tuning	for more than 2 seconds on the remote
Others	control.

Disc

6 To change the code on the remote control

While pressing [ENTER], press and hold the numbered button ([1], [2] or [3]) for more than 2 seconds.

7 Press [ENTER].

∫When the following indicator appears on the unit’s display

The unit’s remote control code

Change the code on the remote control to match the main unit’s (➡step 6).

[Note]

Executing “Shipping Condition” in the SETUP menu returns the main unit code to “DVD 1”. Change the remote control code to 1 (➡step 6).

Getting started

RQT7462

11

Image 11

Contents Instructions carefully Performance and safety, please read theseBefore connecting, operating or adjusting this ExampleThis Unit is Intended for USE in Moderate Climates Getting startedUseful features Table of contentsUse AccessoriesPlease check and identify the supplied accessories Getting BatteriesUnit’s display Remote controlControl reference guide Main unitEmpty When the unit is not to be used for a long timeDo not connect the unit through a video cassette recorder Before moving the unit, ensure the disc tray isVideo OUT terminal Connecting to a television with 21-pin Scart TerminalConnecting to a VCR with 21-pin Scart terminal Component video outputOptical digital audio cable Connecting an amplifier or system componentConnection Amplifier’s rear panelPress 3, 4 to select the country and press Enter Auto-SetupPress 3, 4 to change the setting Press Enter when you have finished the settingsTo enjoy progressive video Press 3, 4, 2, 1 to select Setup and press EnterSelecting television type and aspect Press FunctionsTelevision operation When the following indicator appears on the unit’s displayPoint the remote control at the television To change the code on the remote controlDiscs that cannot be played HDD and Disc informationHDD and discs you can use for recording and play Play-only discs 12 cm/8 cmGetting HDD Hard disk drive handling carePress ¥ REC to start recording Recording television programmesPress W X CH to select the channel Press Time Slip Recording modes and approximate recording timesPlaying while you are recording Press 1 PlayPress 3, 4, 2, 1 to select Start and press Enter Press REC Mode to select Recording mode XP, SP, LP or EPFlexible Recording Recording from an external equipmentPress G-Code Timer recordingUsing G-CODEsystem to make timer recordings Press F TimerPress 1 to move through the items Manually programming timer recordingsPress 3, 4 to select New Timer Press PROG/CHECKTo change a programme To exit the timer recording listTo put the unit on timer recording standby Check, change or delete a programmePlaying Playing discsPress 1 Play BackManual Skip Operations during playSkipping the specified Time Time SlipPress Erase Press 2, 1 to select Erase and press Enter Editing operations during playChanging audio Press AudioPress TOP Menu Using menus to play MP3Using the tree screen to find a group Press 3, 4, 2, 1 to select a groupPress Display Using on-screen menus and Status messagesDisc menu-Setting the disc content On-screen menusPicture menu-Change the picture quality Status messagesPress Status Play menu-Change the play sequencePress 3, 4, 2, 1 to select the chapter Editing titles/chaptersEditing titles/chapters and playing chapters Press Direct Navigator Press 3, 4, 2, 1 to select the titleChapter operations Cancel Protection §Title operations Creating play lists Press 3 to cancelCreating, editing and playing play lists Press 3, 4, 2, 1 to select Play List and press EnterChapter Editing and playing play lists/chaptersPlay list operations MoveCharacter and press Enter Entering textShow Enter Name screen Press 3, 4, 2, 1 to select aTransfer Dubbing Transferring dubbing titles or play listsDubbing One Touch Transfer dubbingPress Dubbing Press Enter to confirmDubbing Press 3, 4 to select Start Dubbing and press EnterTransferring dubbing a finalized DVD-R To edit the transferring dubbing listPress 3, 4 to select the operation and press Enter Functions windowPress 3, 4, 2, 1 to select an item and press Enter Press 3, 4, 2, 1 to select Disc Management and press EnterFormat Disc Disc NameTop Menu Disc ProtectionFunctions Changing the unit’s settingsCommon procedures Summary of settingsPicture Tabs Menus Options Underlined items are the factory presetsConvenient functions Bilingual Audio Selection Audio Mode for XP RecordingPlay k1.3 & Audio during Search Dynamic Range Compression DVD-VDolby Digital onlyAV2 Input ProgressiveTV System AV1 OutputTo select a TuningPress 3, 4 to select Manual and press Enter Press 3, 4, 2Press 2, 1 to select the country and press Enter Press 3, 4 to select Auto-Setup Restart and press EnterTo change the setting all at once PAL!#NTSC Press 2, 1 to select Yes and press EnterClock starts Clock settingsTo cancel the Child Lock Child LockReference SpecificationsGlossary Recording Frequently asked questionsSet upPage CoverOn the unit’s display Error messagesOn the television ≥Set the clock Display Troubleshooting guide≥Select On in Grey Background in the Setup menu Troubleshooting guide Ratings password Even when is pressedDVD-R disc using the high Speed mode When transferring dubbingErase operation Safety precautions MaintenanceIndex

Related manuals

Manual 54 pages 58.34 Kb