Mitsubishi Electronics HS-U778 manual Timer Recording Hints, Auto speed programming

Page 35

Timer Recording

Timer Recording Hints

To use the VCR before timer recording begins, press POWER on the remote once. This turns the programmed recording light off and the VCR on.

If you use POWER on the front panel for this purpose, press it twice. Pressing it once turns off the programmed recording light; pressing it again turns the VCR on.

When you are finished using theVCR, turn the VCR power off again. Make sure the programmed recording light is back on.

After a program has been recorded, the VCR memory of that program is cleared (unless you have scheduled the VCR to record the program every day or every week).

If there is already a program in the VCR’s memory, you will see the Recap screen when you bring up the menus for programming to record (unless you are programming with the QUICK PROGRAM/VCR Plus+). If the VCR’s memory is full, Program memory is full will appear on the screen. If so, you must erase a program before you can enter a new one.

If a tape runs out during timer recording, the VCR ejects the tape and the programmed recording light and the tape status symbol will flash. Load a new tape and press REC. Recording will resume.

If you forget to load a tape, the programmed recording light and the tape status symbol will flash when you turn the VCR power off (A tape without an erasure tab will be ejected. To correct this, load a tape with its erasure tab intact, and turn off the VCR.).

Do not overlap the recording times you enter into the VCR. If you set two programmed recording times overlap,VCR is already programmed for that time will appear on your screen.

Remember that the VCR will record over the next section of tape. If you want to save a tape, remove it and instead use a different tape for a new recording.

Your VCR will not record over a tape that has the erasure prevention tab removed. All rental movies have this tab removed, so they are safe from being accidentally erased.

Auto speed programming

Use auto speed programming if you want to record as much of the program as possible in standard play (SP) speed, but you want the VCR to automatically switch to extended play (EP) if there is not enough tape left.

Auto speed programming is only available for one program. In the first slot, the recording speed default is AUTO.

Make sure that the Tape video function matches the length of tape you are using. See Selecting and adjusting the audio and video functions on page 27.

At the point where the recording mode changes from standard play (SP) to extended play (EP), some noise and/or sound may be in the picture when playing the tape.

VCR

POWER

1

2

3

4

5

6

7

8

9

 

0

X2

POWER

PROG REC

PROG REC

REC

1

2

3

 

 

4

5

6

PROG REC

REC

7

0

X2

8

9

 

 

2 REC LENGTH

PROG REC

33

Image 35
Contents Video Cassette Recorder OWNER’S Guide Special Features HS-U778 Shortcuts Power Lines CleaningAccessories Power SourcesServicing Replacement PartsSafety Check OverloadingChoosing a Hookup Hooking Up Your VCRUnpacking Your VCR Hooking UpYourVCR Antenna or Cable System without Cable BoxCable System with Cable Box Hooking Up Your VCR Connections to TV with Audio Video InputsDSS is a registered trademark of DirecTV, Inc Connections to Satellite ReceiverConnections to Home Theater Receiver Connections to IR Emitter Connections to A/V NetworkTV without Audio/Video Inputs Setting UpYour VCRPlayback TV with Audio/ Video InputsPlayback OperatingYour Remote ControlLoading a Tape Playing a TapeUnloading a Tape Using Basic Playback ControlsMemorizing Channels Automatically Setting UpYour VCRÄChannel Setting Up Your VCRIf you choose Cable or Indoor/outdoor ant If you choose Cable box only or Digital cable box only±Sat.receiver OFF Setting UpYourVCRSatellite Receiver Control Sony Dish Network Toshiba Panasonic Hughes None Adding and Deleting ChannelsSelecting satellite channels sequentially Selecting a ChannelDigital cable box Selecting antenna, cable or digital cable channels directlyÄClock set Setting the ClockSetting the Auto Clock ÄChannel Auto Setting the Clock ManuallyIf theVCR displays the wrong time ÄMonth March EnterRecording a Current Broadcast RecordingHow OTR affects other controls Using One-Touch Recording OTRIf you program too much time into the OTR timer RecordingHow OTR2 affects other controls Using Standby One-Touch Recording OTR2To cancel OTR2 If you use VHS tape for recording Using S-VHS Set-Up MenuSelecting Recording Format If you use S-VHS tape for recordingÄRear S-input Selecting S-input SettingUsing S-through ÄFront S-inputNormal recording Record Using Audio and Video FunctionsDescriptions of Audio Functions Audio monitor Listen toDescriptions ofVideo Functions Selecting and adjusting the audio and video functionsVCR Plus+ system programming easy Timer RecordingConventional VCR Timer Recording ConventionalVCR timer recordingÄRecord speed Timer RecordingÄDay ÄStart timeChanging while programming Canceling a recording in progressThere are two ways to cancel a recording in progress Quick ProgramÄOnce ÄDaily ÄWeekly VCR Plus+ System ProgrammingEach week After you have made your choice, press Enter¤ 2 MO11 1130a 130pSP Auto speed programming Timer Recording HintsProgram caution Program skip using menusProgram skip using the Power button Changing timer recording settingsMemory backup Canceling a timer recording before the recording startsUsing a satellite receiver Using the HS-U778 to record from another VCR Editing FeaturesUsing Two VCRs to Copy Using the HS-U778 to playback to another VCR Editing FeaturesSpecial effects Advanced FeaturesAdvanced Playback Controls Time Counter Adjusting the TrackingAdvanced Features Speed search Searching TechniquesQuick search CM skip Manual index marks Counter zero stopIndex search Automatic index marksMemorizing the contents of the tape Using PrograManagerTape No.0 Page 1/1 ÄAssign/Enter Tape No. ÄDisplay memorized dataSep Sat 1000a Searching the recorded programÄDisplay current data ÄDisplay memorized data Tape No.0 Confirming/erasing the memorized dataTo make the time gauge and the remaining time appear Displaying the Current TimeVideo mute Auto power save auto-offCustomize Choices Menu PerfecTape Setting up PerfecTapeUsing PerfecTape automatically RF converterÄRental Xpress Using PerfecTape manuallyRental Xpress Active A/V Network ÄYes ÄNo Auto PrograManagerAdvanced Options Using the remote control to operate your TVSetting up your remote control to operate your TV Operating your TV with the HS-U778 remote controlChild Lock To program the remote control operational settingWhen you wish to operate the other VCR To reprogram the HS-U778 to respond to VCR-A signals againLocation of Controls Remote ControlFront Panel Front Panel Display Location of ControlsRear Panel Jacks Closed Captioning Important InformationVideo game patterns and scoreboards Trouble Checks Problem Try ThisTrouble Checks Index SpecificationsIndex Page Page Mitsubishi Video Cassette Recorder Limited Warranty WarrantyFor your nearest Mitsubishi Authorized Service Center call