Mitsubishi Electronics HS-U778 Advanced Options, Using the remote control to operate your TV

Page 54

Advanced Features

Advanced Options

Using the remote control to operate your TV

The HS-U778 remote control can operate many of the frequently-used functions of your TV. You only need one remote to operate both your VCR and TV.

The HS-U778 remote control is pre-set to operate Mitsubishi televisions, but it can also operate TVs from other manufacturers. To set your remote control for your particular brand of television, follow these instructions.

setting up your remote control to operate your TV

1Turn off your TV.

2On the HS-U778 remote control, set the VCR/TV slide switch to TV position.

3While holding in SP/EP, press the brand code button listed that corresponds to the brand of your TV.

4Press TV POWER on the HS-U778 remote control. Once your TV has turned on, your remote is set up to operate your brand of TV.

If your TV does not turn on, repeat step 3 using the next code listed for the brand of your TV.

If none of the codes listed for the brand of your TV work, then repeat step 3 several times, using a different code button until one works. The possible code buttons are: 0, 1-9, MUTE,VOLUME »,¼, CHANNEL»,¼ and INPUT.

You do not need to perform this set-up again until you change the batteries, set up your remote for another brand of television, or you get a new TV.

Once you have correctly set your remote control to operate your TV, you will be able to use the TV POWER, CHANNEL,VOLUME, and number buttons to operate your TV.

IMPORTANT

Because of variations among models, some or all buttons may not work, or they may operate different functions than expected for your particular TV. If this occurs, you may need to use your TV remote control.

Sometimes manufacturers will change the remote control codes for their products, or they will use more than one code. If this is the case, your remote may not be able to control your TV.

When you replace the batteries in your remote, the remote may return to its initial setting (code button 1). Repeat the steps above to reset your remote control. If you enter a new code, the previous code will be erased.

operating your TV with the HS-U778 remote control

1Set the VCR/TV slide switch to TV position on the HS-U778 remote control to tell the remote that you want to operate the TV.

2Point the remote control towards the TV and press the desired buttons. To once again control theVCR, set the VCR/TV slide switch to VCR position.

Brand of TV

Brand code

 

buttons

Mitsubishi

1, 2, 3

Fisher

0

G.E.

VOLUME »

Goldstar

2, 9

Hitachi

8

JVC

MUTE

Magnavox

4

NEC

2, 9

Panasonic

CHANNEL»,¼

Pioneer

6

Philips

4

Proscan

VOLUME »

Quasar

CHANNEL¼

RCA

VOLUME» ￿

Sanyo

0

Sharp

3, 5

Sony

VOLUME¼

Toshiba

7

Zenith

INPUT

1 2 3

4 5 6

7 8 9

0 X2

VCR

TV

52

Image 54
Contents Video Cassette Recorder OWNER’S Guide Special Features HS-U778 Shortcuts Power Sources CleaningAccessories Power LinesOverloading Replacement PartsSafety Check ServicingHooking Up Your VCR Unpacking Your VCRChoosing a Hookup Antenna or Cable System without Cable Box Cable System with Cable BoxHooking UpYourVCR Connections to TV with Audio Video Inputs Hooking Up Your VCRConnections to Satellite Receiver DSS is a registered trademark of DirecTV, IncConnections to Home Theater Receiver Connections to A/V Network Connections to IR EmitterTV with Audio/ Video Inputs Setting UpYour VCRPlayback TV without Audio/Video InputsPlaying a Tape OperatingYour Remote ControlLoading a Tape PlaybackUsing Basic Playback Controls Unloading a TapeSetting UpYour VCR Memorizing Channels AutomaticallyIf you choose Cable box only or Digital cable box only Setting Up Your VCRIf you choose Cable or Indoor/outdoor ant ÄChannelSetting UpYourVCR Satellite Receiver Control±Sat.receiver OFF Adding and Deleting Channels Sony Dish Network Toshiba Panasonic Hughes NoneSelecting antenna, cable or digital cable channels directly Selecting a ChannelDigital cable box Selecting satellite channels sequentiallySetting the Clock Setting the Auto ClockÄClock set Setting the Clock Manually If theVCR displays the wrong timeÄChannel Auto Enter ÄMonth MarchRecording Recording a Current BroadcastRecording Using One-Touch Recording OTRIf you program too much time into the OTR timer How OTR affects other controlsUsing Standby One-Touch Recording OTR2 To cancel OTR2How OTR2 affects other controls If you use S-VHS tape for recording Using S-VHS Set-Up MenuSelecting Recording Format If you use VHS tape for recordingÄFront S-input Selecting S-input SettingUsing S-through ÄRear S-inputAudio monitor Listen to Using Audio and Video FunctionsDescriptions of Audio Functions Normal recording RecordSelecting and adjusting the audio and video functions Descriptions ofVideo FunctionsConventionalVCR timer recording Timer RecordingConventional VCR Timer Recording VCR Plus+ system programming easyÄStart time Timer RecordingÄDay ÄRecord speedQuick Program Canceling a recording in progressThere are two ways to cancel a recording in progress Changing while programmingAfter you have made your choice, press Enter VCR Plus+ System ProgrammingEach week ÄOnce ÄDaily ÄWeekly¤ 2 MO11 1130a 130pSP Timer Recording Hints Auto speed programmingChanging timer recording settings Program skip using menusProgram skip using the Power button Program cautionCanceling a timer recording before the recording starts Using a satellite receiverMemory backup Editing Features Using Two VCRs to CopyUsing the HS-U778 to record from another VCR Editing Features Using the HS-U778 to playback to another VCRAdvanced Features Advanced Playback ControlsSpecial effects Adjusting the Tracking Advanced FeaturesTime Counter Searching Techniques Quick search CM skipSpeed search Automatic index marks Counter zero stopIndex search Manual index marksUsing PrograManager Memorizing the contents of the tapeÄAssign/Enter Tape No. ÄDisplay memorized data Tape No.0 Page 1/1Searching the recorded program ÄDisplay current data ÄDisplay memorized dataSep Sat 1000a Confirming/erasing the memorized data Tape No.0Displaying the Current Time To make the time gauge and the remaining time appearAuto power save auto-off Customize Choices MenuVideo mute RF converter Setting up PerfecTapeUsing PerfecTape automatically PerfecTapeUsing PerfecTape manually Rental XpressÄRental Xpress Active A/V Network Auto PrograManager ÄYes ÄNoOperating your TV with the HS-U778 remote control Using the remote control to operate your TVSetting up your remote control to operate your TV Advanced OptionsTo reprogram the HS-U778 to respond to VCR-A signals again To program the remote control operational settingWhen you wish to operate the other VCR Child LockRemote Control Location of ControlsFront Panel Location of Controls Front Panel DisplayRear Panel Jacks Important Information Video game patterns and scoreboardsClosed Captioning Problem Try This Trouble ChecksTrouble Checks Specifications IndexIndex Page Page Warranty Mitsubishi Video Cassette Recorder Limited WarrantyFor your nearest Mitsubishi Authorized Service Center call