Runco LS-10D operation manual Time after turning on the system, Adjusting the Lens Position

Page 60

Installation

3. Select Service from the Main Menu and enter the Service Menu passcode.

Note

You must enter a passcode to access the Service menu for the first

time after turning on the system.

4.Select Triggers from the Service menu.

5.Assign the trigger output to which the lens motor is connected to the Cinema and Virtual Cinema aspect ratios. This enables the lens motor to move the anamorphic lens into position (in front of the primary lens) when either aspect ratio is selected.

6.Select the Cinema aspect ratio to move the anamorphic lens into position, if it isn’t already. To do this, press CINEMA on the DHD Controller remote control (Figure 2-6), or press or repeatedly with no menus visible on-screen.

Adjusting the Lens Position:

1.Adjust the vertical position and tilt of the lens so that the projector beam is passing through the center of the lens and any residual pincushion distortion is about the same at the top and bottom of the image. This typically results in the anamorphic lens being below the center of the primary lens and tilted slightly downward.

2.Tighten the knobs.

There may be some pincushion distortion even after the lens is

Note properly adjusted, especially at shorter throw distances. If this is the case, Runco recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

3.Adjust the rotation of the Lens Transport Assembly so that the left and right sides of the image are an equal distance from their respective screen borders.

4.Tighten the Pivot Screw and the four mounting screws holding the transport to the Attachment Plate.

5.For optimum multiple aspect ratio performance, adjust the projector’s zoom so that a 1.85:1 aspect ratio movie is just masked by the top and bottom of the screen border when the anamorphic lens is not in front of the primary lens. This way 1.85:1, 16:9 and 2.35-2.4:1 aspect ratio movies are all presented to fill the screen at a constant height.

6.Remove the protective film from the front of the anamorphic lens.

44

Runco LS-10d Installation/Operation Manual

Page 59 Page 61
Image 60
Page 59 Page 61
Contents LS-10d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsExternal Control Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions LS-10d at a GlanceProjection Lens Runco Logo Badge Rear Cover Power Input 100 to 240 VAC Connect the LS-10d to power here LS-10d Rear PanelControl the anamorphic lens transport Other equipment to the DHD ControllerDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear Panel USBRS-232 To Accessory Box Component / Scart 3 x RCA connectorsDisplay Control Video 1 / Video 2 / VideoLS-10d Remote Control Unit DHD Controller/LS-10d Remote ControlMemory Preset Buttons On / OFFCursor Buttons For more information about aspect ratios, refer to TableHD 1 4 / HD 2 Comp ComponentHdmi 1 7 / Hdmi 2 8 / Hdmi 3 / Hdmi 4 ScartInstallation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Ambient Light Throw DistanceEstimating Throw Distance LS-10d Lens Options and Throw Ratios Note Throw Range Throw Ratio Inches, withLens Option LensCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Synchronization Issues Possible Audio Latency for Various Input TimingsAudio/Video Input Timing Possible Audio Latency millisecondsInstalling the Optional Anamorphic Lens Mount Package ContentsOther Considerations Attaching the Transport Assembly Attachment Plate Assembly Attachment plate Ceiling Mount Plate Attachment Plate Projector bottomPlate Installation Installing the Projector Mounting the LS-10dFloor Mounting Upright Ceiling Mounting Inverted An EnclosureAdjusting the Projection AngleConnector Panel Access Connections toLS-10d and DHD ControllerConnecting the DHD Controller to the LS-10dUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workConnecting Source Components to the DHDController Hdmi Source Connections See FigureComponent Video Source Connections 10. Rgbhv Source Connections 11. Scart Rgbs Source Connections Composite Source Connections See Figure RS-232 ControllerConnection Connecting 12-volt Trigger Outputs to External Equipment +12V Trigger InputConnecting an External IR Receiver to the DHDTurning on the Power Connecting to AC PowerPrimary Lens Adjustments Adjusting the Picture OrientationYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftAdjusting the Image Geometry 17. Keystone and Pincushion DistortionYou must enter a passcode to access the Calibration menu Left Middle y setting also controls the Right MiddleInstalling and Adjusting the Anamorphic Lens InstallationAdjustment It is extremely important that the primary lens is properlyAdjusting the Lens Position Time after turning on the systemUsing the On-Screen Menus OperationService CUEMain Menu Input SourceAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirRemote Aspect Ratio Control Description Key NativePicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep TimerInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesModes on a given input X/y Color Gamut Values Given inputColor Hue Saturation Hue SaturationHue Copied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Operation If a Display Error, a device-specific Operation Firmware Upgrade functions Onoff Operation 56 and ISF Day/Night Memory Presets Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Port Configuration Serial Command SyntaxExternal Control Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsMiscellaneous Commands Enter keyExit key Using Discrete IR Codes Command Parameter Value Description Min/maxCommand Bits With Toggle Bit = Hex Binary Function StartIR Command List Remote Control With Toggle Description Button Name Bit =RC5 Control Codes for the DHD Controller RC5 DataEnter ST90MIN Using Hdmi CEC Messages CEC Commands Supported by the DHD ControllerOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control Specifications LS-10d SpecificationsLS-10d Specifications Home Theater Calibration Specifications Industry-Standard SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsLS-10d Dimensions LS-10d DimensionsSupported Signal Timings by Input Format Resolution Frequency Rate Hz MHz KHzSupported Timings HorizontalComponent Composite 1 Composite 2 CompositePAL-M Specifications Page 020-1073-00 Rev. a September

LS-10D specifications

The Runco LS-10D is a high-performance projector that is captivating audiences with its exceptional image quality and advanced features. Designed for home cinema enthusiasts, the LS-10D combines cutting-edge technology and stylish aesthetics to deliver an immersive viewing experience that is second to none.

One of the standout features of the LS-10D is its remarkable color performance. Utilizing Runco's proprietary Vivix processing, the projector achieves a color accuracy that is unparalleled in the industry. This technology ensures that images appear vibrant and true to the original source material, making movies, sports, and gaming more engaging than ever. The LS-10D also supports a wide color gamut, enabling it to reproduce a broad spectrum of colors, resulting in lifelike images that captivate viewers.

Another noteworthy characteristic of the LS-10D is its resolution capabilities. The projector boasts a native resolution of 1080p, delivering sharp and detailed images that enhance the overall viewing experience. For users looking for even greater clarity, the LS-10D is also compatible with 4K content through its advanced upscaling technology, allowing it to present finer details in high-resolution formats without losing quality.

The LS-10D employs an advanced lamp technology, producing an impressive brightness level that ensures excellent performance even in well-lit environments. This capability makes it ideal for a variety of settings, from dedicated home theaters to living rooms where ambient light cannot be controlled. Users will appreciate the projectors' reliable light source that enhances contrast and reduces the risk of color fading over time.

To further complement its impressive features, the LS-10D incorporates a range of connectivity options. This includes HDMI inputs, component video inputs, and RS-232 control, allowing for seamless integration with various sources such as Blu-ray players, gaming consoles, and home automation systems.

Additionally, the LS-10D's sleek and compact design makes it an attractive addition to any home theater setup. With its quiet operation and efficient cooling system, users can enjoy their favorite films without the distraction of fan noise.

In conclusion, the Runco LS-10D is a powerful projector that stands out for its exceptional image quality, advanced technologies, and user-friendly features. With its array of capabilities, it provides a premium home cinema experience that is sure to impress even the most discerning movie aficionados.
Top Page Image Contents