Runco LS-10D operation manual Overscan Modes

Page 71

Operation

Height: Select Height from the Input Position menu to change the projected image height. Press to increase the height; press to decrease it.

Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Overscan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.

This control defines the amount of overscan applied to the image. The range is from

0 to 20. There are two overscan modes:

•In Crop mode, each increment adds a mask at the top, bottom, left and right edges of the source image equal to 0.5% of the displayed horizontal resolution (1% total). A setting of 10, for example, crops the image 5% on all sides or 10% total.

•In Zoom mode, each increment adds a factor to the scaling of the source image so that the vertical and horizontal resolutions are 100% plus 1% increments of the size determined by the aspect ratio function. A setting of 10, for example, zooms in on the image 5% on all sides or 10% total.

Figure 4-6illustrates the effect of each overscan mode setting.

Off

Crop

Zoom

4:3

16:9

= Source Image Area

= Edge Noise

= Screen (16:9)

Figure 4-6. Overscan Modes

Runco LS-10d Installation/Operation Manual

55

Page 70 Page 72
Image 71
Page 70 Page 72
Contents LS-10d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation External Control Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationFormat screen Description, Features and BenefitsOptional Accessories LS-10d at a Glance Controls and FunctionsProjection Lens Runco Logo Badge Rear Cover Other equipment to the DHD Controller Power Input 100 to 240 VAC Connect the LS-10d to power hereLS-10d Rear Panel Control the anamorphic lens transportDHD Controller Front Panel DHD Controller Front PanelUSB DHD Controller Rear PanelVideo 1 / Video 2 / Video RS-232 To Accessory BoxComponent / Scart 3 x RCA connectors Display ControlDHD Controller/LS-10d Remote Control LS-10d Remote Control UnitFor more information about aspect ratios, refer to Table Memory Preset ButtonsOn / OFF Cursor ButtonsScart HD 1 4 / HD 2Comp Component Hdmi 1 7 / Hdmi 2 8 / Hdmi 3 / Hdmi 4Installation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Estimating Throw Distance Ambient LightThrow Distance Lens LS-10d Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with Lens OptionPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input Timings Audio/VideoOther Considerations Installing the Optional Anamorphic Lens MountPackage Contents Attaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Assembly Attachment platePlate Installation An Enclosure Installing the ProjectorMounting the LS-10d Floor Mounting Upright Ceiling Mounting InvertedAngle Adjusting the ProjectionController Connector Panel AccessConnections to LS-10d and DHDDVI-to-HDMI adapters will not work Connecting the DHDController to the LS-10d Use an Hdmi cable for this connection. a DVI cable withHdmi Source Connections See Figure Connecting SourceComponents to the DHD ControllerComponent Video Source Connections 10. Rgbhv Source Connections 11. Scart Rgbs Source Connections Connection Composite Source Connections See FigureRS-232 Controller +12V Trigger Input Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift Primary Lens AdjustmentsAdjusting the Picture Orientation You must enter a passcode to access the Service menu17. Keystone and Pincushion Distortion Adjusting the Image GeometryLeft Middle y setting also controls the Right Middle You must enter a passcode to access the Calibration menuIt is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic LensInstallation AdjustmentTime after turning on the system Adjusting the Lens PositionOperation Using the On-Screen MenusCUE ServiceAspect Ratio Main MenuInput Source Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsNative Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep TimerShould be used by ISF-certified technicians only InformationCalibration CIE 1931 Chromaticity Diagram Modes on a given input Color Temperature Presets and Associated Color PointsColor Temperature Preset Associated x/y Values Color X/y Color Gamut ValuesGiven input Hue Hue SaturationHue Saturation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Operation If a Display Error, a device-specific Operation Firmware Upgrade functions Onoff Operation 56 and ISF Day/Night Memory Presets Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Serial Communications Port ConfigurationSerial Command Syntax External ControlInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit key Miscellaneous CommandsEnter key With Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Parameter Value Description Min/max Command BitsRC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD ControllerEnter ST90MIN Opcode Value Supported? √ = Yes, = No Initiator Follower Using Hdmi CEC MessagesCEC Commands Supported by the DHD Controller Messages from the Hdmi Audio Out connector External Control LS-10d Specifications SpecificationsLS-10d Specifications Limited Warranty Home Theater Calibration SpecificationsIndustry-Standard Specifications Weight without lensDHD Controller Specifications DHD Controller SpecificationsLS-10d Dimensions LS-10d DimensionsHorizontal Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported TimingsComposite 1 Composite 2 Composite ComponentPAL-M Specifications Page 020-1073-00 Rev. a September

LS-10D specifications

The Runco LS-10D is a high-performance projector that is captivating audiences with its exceptional image quality and advanced features. Designed for home cinema enthusiasts, the LS-10D combines cutting-edge technology and stylish aesthetics to deliver an immersive viewing experience that is second to none.

One of the standout features of the LS-10D is its remarkable color performance. Utilizing Runco's proprietary Vivix processing, the projector achieves a color accuracy that is unparalleled in the industry. This technology ensures that images appear vibrant and true to the original source material, making movies, sports, and gaming more engaging than ever. The LS-10D also supports a wide color gamut, enabling it to reproduce a broad spectrum of colors, resulting in lifelike images that captivate viewers.

Another noteworthy characteristic of the LS-10D is its resolution capabilities. The projector boasts a native resolution of 1080p, delivering sharp and detailed images that enhance the overall viewing experience. For users looking for even greater clarity, the LS-10D is also compatible with 4K content through its advanced upscaling technology, allowing it to present finer details in high-resolution formats without losing quality.

The LS-10D employs an advanced lamp technology, producing an impressive brightness level that ensures excellent performance even in well-lit environments. This capability makes it ideal for a variety of settings, from dedicated home theaters to living rooms where ambient light cannot be controlled. Users will appreciate the projectors' reliable light source that enhances contrast and reduces the risk of color fading over time.

To further complement its impressive features, the LS-10D incorporates a range of connectivity options. This includes HDMI inputs, component video inputs, and RS-232 control, allowing for seamless integration with various sources such as Blu-ray players, gaming consoles, and home automation systems.

Additionally, the LS-10D's sleek and compact design makes it an attractive addition to any home theater setup. With its quiet operation and efficient cooling system, users can enjoy their favorite films without the distraction of fan noise.

In conclusion, the Runco LS-10D is a powerful projector that stands out for its exceptional image quality, advanced technologies, and user-friendly features. With its array of capabilities, it provides a premium home cinema experience that is sure to impress even the most discerning movie aficionados.
Top Page Image Contents