Runco LS-10D operation manual Firmware Upgrade functions

Page 85

Operation

•Remote Network Control: Select Remote Network Control from the Network menu to enable or disable control of the DHD Controller via an IP connection (typically using a web browser). Set it to On to allow all incoming remote network connectivity. Set it to Off to disable any incoming network communication that was not initiated by the DHD Controller.

Note

This setting has no effect on the E-Mail Notification or Auto

Firmware Upgrade functions.

Color Space: Select Color Space from the Service menu to choose the color space of the source signal for HDMI, RGB, and component connections.

•The default setting, Auto, functions as follows:

•HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/or range data, the DHD Controller uses that information. Otherwise, for RGB sources, the DHD Controller uses the RGB-Videocolor space. For component SDTV and EDTV resolutions, REC601 is used. For other component video resolutions, REC709 is used.

•RGB: If Hsync or Vsync signals are present, the DHD Controller uses the RGB-PCcolor space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709 for all other sources.

•Component: For SDTV and EDTV resolutions, the DHD Controller uses the REC601 color space. For all other resolutions, REC709 is used.

In most cases, the Auto setting determines the correct color space to use. If it does not, you can force the DHD Controller to use a specific color space. Choose one of the following:

•REC709 sets the color space matrix to that defined in ITU-R BT.709.

•REC601 sets the color space matrix to that defined in ITU-R BT.601.

•RGB-PCuses RGB color space and sets black at 0,0,0 RGB and white at 255,255,255 RGB, assuming an 8-bit image.

•RGB-Videouses RGB color space and sets black at 16,16,16 RGB and white at 235,235,235, assuming an 8-bit image, to correspond to the luminance values defined in digital component standards.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

If your LS-10d is equipped with an anamorphic lens, assign at least one trigger output (the same one to which the lens motor is connected) to the Cinema and Virtual Cinema aspect ratios.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language (English, Français, Deutsch, Italiano, Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).

•OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer, which controls how long the menus remain on-screen after selecting them. Select from 5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want the menus to remain on-screen indefinitely.

Runco LS-10d Installation/Operation Manual

69

Page 84 Page 86
Image 85
Page 84 Page 86
Contents LS-10d Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures Xvi About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories LS-10d at a Glance Controls and FunctionsProjection Lens Runco Logo Badge Rear Cover LS-10d Rear Panel Power Input 100 to 240 VAC Connect the LS-10d to power hereControl the anamorphic lens transport Other equipment to the DHD ControllerDHD Controller Front Panel DHD Controller Front PanelUSB DHD Controller Rear PanelComponent / Scart 3 x RCA connectors RS-232 To Accessory BoxDisplay Control Video 1 / Video 2 / VideoDHD Controller/LS-10d Remote Control LS-10d Remote Control UnitOn / OFF Memory Preset ButtonsCursor Buttons For more information about aspect ratios, refer to TableComp Component HD 1 4 / HD 2Hdmi 1 7 / Hdmi 2 8 / Hdmi 3 / Hdmi 4 ScartRemote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient LightEstimating Throw Distance Throw Range Throw Ratio Inches, with LS-10d Lens Options and Throw Ratios NoteLens Option LensFloor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Possible Audio Latency for Various Input Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsPackage Contents Installing the Optional Anamorphic Lens MountOther Considerations Attaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Assembly Attachment platePlate Installation Mounting the LS-10d Installing the ProjectorFloor Mounting Upright Ceiling Mounting Inverted An EnclosureAngle Adjusting the ProjectionConnections to Connector Panel AccessLS-10d and DHD ControllerController to the LS-10d Connecting the DHDUse an Hdmi cable for this connection. a DVI cable with DVI-to-HDMI adapters will not workComponents to the DHD Connecting SourceController Hdmi Source Connections See FigureComponent Video Source Connections 10. Rgbhv Source Connections 11. Scart Rgbs Source Connections RS-232 Controller Composite Source Connections See FigureConnection +12V Trigger Input Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerAdjusting the Picture Orientation Primary Lens AdjustmentsYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens Shift17. Keystone and Pincushion Distortion Adjusting the Image GeometryLeft Middle y setting also controls the Right Middle You must enter a passcode to access the Calibration menuInstallation Installing and Adjusting the Anamorphic LensAdjustment It is extremely important that the primary lens is properlyTime after turning on the system Adjusting the Lens PositionOperation Using the On-Screen MenusCUE ServiceInput Source Main MenuAspect Ratio Remote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirNative Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerCalibration InformationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsModes on a given input Given input X/y Color Gamut ValuesColor Hue Saturation Hue SaturationHue Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Operation If a Display Error, a device-specific Operation Firmware Upgrade functions Onoff Operation 56 and ISF Day/Night Memory Presets Lamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsEnter key Miscellaneous CommandsExit key Command Parameter Value Description Min/max Using Discrete IR CodesCommand Bits With Toggle Bit = Hex Binary Function StartRemote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter ST90MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control LS-10d Specifications SpecificationsLS-10d Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsWeight without lens Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsLS-10d Dimensions LS-10d DimensionsFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings HorizontalComposite 1 Composite 2 Composite ComponentPAL-M Specifications Page 020-1073-00 Rev. a September

LS-10D specifications

The Runco LS-10D is a high-performance projector that is captivating audiences with its exceptional image quality and advanced features. Designed for home cinema enthusiasts, the LS-10D combines cutting-edge technology and stylish aesthetics to deliver an immersive viewing experience that is second to none.

One of the standout features of the LS-10D is its remarkable color performance. Utilizing Runco's proprietary Vivix processing, the projector achieves a color accuracy that is unparalleled in the industry. This technology ensures that images appear vibrant and true to the original source material, making movies, sports, and gaming more engaging than ever. The LS-10D also supports a wide color gamut, enabling it to reproduce a broad spectrum of colors, resulting in lifelike images that captivate viewers.

Another noteworthy characteristic of the LS-10D is its resolution capabilities. The projector boasts a native resolution of 1080p, delivering sharp and detailed images that enhance the overall viewing experience. For users looking for even greater clarity, the LS-10D is also compatible with 4K content through its advanced upscaling technology, allowing it to present finer details in high-resolution formats without losing quality.

The LS-10D employs an advanced lamp technology, producing an impressive brightness level that ensures excellent performance even in well-lit environments. This capability makes it ideal for a variety of settings, from dedicated home theaters to living rooms where ambient light cannot be controlled. Users will appreciate the projectors' reliable light source that enhances contrast and reduces the risk of color fading over time.

To further complement its impressive features, the LS-10D incorporates a range of connectivity options. This includes HDMI inputs, component video inputs, and RS-232 control, allowing for seamless integration with various sources such as Blu-ray players, gaming consoles, and home automation systems.

Additionally, the LS-10D's sleek and compact design makes it an attractive addition to any home theater setup. With its quiet operation and efficient cooling system, users can enjoy their favorite films without the distraction of fan noise.

In conclusion, the Runco LS-10D is a powerful projector that stands out for its exceptional image quality, advanced technologies, and user-friendly features. With its array of capabilities, it provides a premium home cinema experience that is sure to impress even the most discerning movie aficionados.
Top Page Image Contents