Runco LS-10D operation manual Operation

Page 82

Operation

Network: The options in the Network menu allow you to configure the network communication features.

•IP Configuration: Select IP Configuration from the Network menu to either set the IP address, subnet mask and default gateway of the DHD Controller manually or obtain these settings automatically, from a DHCP (Dynamic Host Configuration Protocol) server. (Most broadband routers and gateways support DHCP.) You can also test the network connection from this menu.

•DHCP: To enable the DHCP client in the DHD Controller, select DHCP from the IP Configuration menu and set it to On. With this setting, the DHD Controller’s IP address, subnet mask and default gateway are assigned by the local DHCP server.

To manually configure these values, set DHCP to Off.

The IP Address, Subnet Mask and Default Gateway items in the IP Note Configuration menu are disabled (grayed out) when DHCP is

enabled.

•IP Address: Select IP Address from the IP Configuration menu to manually configure the IP Address of the DHD Controller, as follows:

1.Press or to select the first, second, third or fourth byte of the address.

2.Press or to set the value of that byte. The range is from 0 to 255 inclusive.

3.Repeat Steps 1 and 2 for all four bytes of the address.

4.Press MENU when you have finished setting the address.

•Subnet Mask: Select Subnet Mask from the IP Configuration menu to manually configure the IP subnet mask. The procedure is similar to that for setting the IP address.

•Default Gateway: Select Default Gateway from the IP Configuration menu to manually configure the default IP gateway. The procedure is similar to that for setting the IP address.

•Communication Test: Select Communication Test from the IP Configuration menu to verify proper operation of the network communication link.

To start the test, select Start Test from the Communication Test menu. The DHD Controller displays the message “Performing Communication Test.” When the test completes, the DHD Controller displays either “Failed” (along with the error that occurred) or “Succeeded.”

•Auto Firmware Upgrade: Select Auto Firmware Upgrade from the Network menu to enable automatic detection of a newer version of the DHD Controller firmware. If one is found, you can configure the DHD Controller to install it automatically. These features make it easier to keep your DHD Controller firmware up-to-date.

•Auto Check For New Firmware: To have the DHD Controller automatically check for firmware updates at periodic intervals, select Auto Check for New Firmware from the Auto Firmware Upgrade menu and set it to On. If you prefer to do this manually, set it to Off and use the Check For New Firmware sub-menu (described below).

•Auto Perform Upgrade: If the “Auto Check For New Firmware” process determines that a newer firmware version than the one currently installed is available, you can have the DHD Controller automatically download and install it. To do this, select Auto Perform Upgrade from the Auto Firmware Upgrade menu and set it to On. The upgrade will occur the next time the DHD Controller is “power-cycled” (powered off, then on again).

66

Runco LS-10d Installation/Operation Manual

Page 81 Page 83
Image 82
Page 81 Page 83
Contents LS-10d Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingExternal Control Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions LS-10d at a GlanceProjection Lens Runco Logo Badge Rear Cover Control the anamorphic lens transport Power Input 100 to 240 VAC Connect the LS-10d to power hereLS-10d Rear Panel Other equipment to the DHD ControllerDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear Panel USBDisplay Control RS-232 To Accessory BoxComponent / Scart 3 x RCA connectors Video 1 / Video 2 / VideoLS-10d Remote Control Unit DHD Controller/LS-10d Remote ControlCursor Buttons Memory Preset ButtonsOn / OFF For more information about aspect ratios, refer to TableHdmi 1 7 / Hdmi 2 8 / Hdmi 3 / Hdmi 4 HD 1 4 / HD 2Comp Component ScartRemote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient LightEstimating Throw Distance Lens Option LS-10d Lens Options and Throw Ratios NoteThrow Range Throw Ratio Inches, with LensVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Audio/Video Synchronization IssuesPossible Audio Latency for Various Input Timings Input Timing Possible Audio Latency millisecondsPackage Contents Installing the Optional Anamorphic Lens MountOther Considerations Attaching the Transport Assembly Attachment Plate Assembly Attachment plate Ceiling Mount Plate Attachment Plate Projector bottomPlate Installation Floor Mounting Upright Ceiling Mounting Inverted Installing the ProjectorMounting the LS-10d An EnclosureAdjusting the Projection AngleLS-10d and DHD Connector Panel AccessConnections to ControllerUse an Hdmi cable for this connection. a DVI cable with Connecting the DHDController to the LS-10d DVI-to-HDMI adapters will not workController Connecting SourceComponents to the DHD Hdmi Source Connections See FigureComponent Video Source Connections 10. Rgbhv Source Connections 11. Scart Rgbs Source Connections RS-232 Controller Composite Source Connections See FigureConnection Connecting 12-volt Trigger Outputs to External Equipment +12V Trigger InputConnecting an External IR Receiver to the DHDTurning on the Power Connecting to AC PowerYou must enter a passcode to access the Service menu Primary Lens AdjustmentsAdjusting the Picture Orientation Focus Zoom Vertical and Horizontal Lens ShiftAdjusting the Image Geometry 17. Keystone and Pincushion DistortionYou must enter a passcode to access the Calibration menu Left Middle y setting also controls the Right MiddleAdjustment Installing and Adjusting the Anamorphic LensInstallation It is extremely important that the primary lens is properlyAdjusting the Lens Position Time after turning on the systemUsing the On-Screen Menus OperationService CUEInput Source Main MenuAspect Ratio Select 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in theirRemote Aspect Ratio Control Description Key NativePicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep TimerCalibration InformationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsModes on a given input Given input X/y Color Gamut ValuesColor Hue Saturation Hue SaturationHue Copied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Operation If a Display Error, a device-specific Operation Firmware Upgrade functions Onoff Operation 56 and ISF Day/Night Memory Presets Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Miscellaneous CommandsExit key Command Bits Using Discrete IR CodesCommand Parameter Value Description Min/max With Toggle Bit = Hex Binary Function StartRC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter ST90MIN CEC Commands Supported by the DHD Controller Using Hdmi CEC MessagesOpcode Value Supported? √ = Yes, = No Initiator Follower Messages from the Hdmi Audio Out connector External Control LS-10d Specifications SpecificationsLS-10d Specifications Weight without lens Home Theater Calibration SpecificationsIndustry-Standard Specifications Limited WarrantyDHD Controller Specifications DHD Controller SpecificationsLS-10d Dimensions LS-10d DimensionsSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz HorizontalComponent Composite 1 Composite 2 CompositePAL-M Specifications Page 020-1073-00 Rev. a September

LS-10D specifications

The Runco LS-10D is a high-performance projector that is captivating audiences with its exceptional image quality and advanced features. Designed for home cinema enthusiasts, the LS-10D combines cutting-edge technology and stylish aesthetics to deliver an immersive viewing experience that is second to none.

One of the standout features of the LS-10D is its remarkable color performance. Utilizing Runco's proprietary Vivix processing, the projector achieves a color accuracy that is unparalleled in the industry. This technology ensures that images appear vibrant and true to the original source material, making movies, sports, and gaming more engaging than ever. The LS-10D also supports a wide color gamut, enabling it to reproduce a broad spectrum of colors, resulting in lifelike images that captivate viewers.

Another noteworthy characteristic of the LS-10D is its resolution capabilities. The projector boasts a native resolution of 1080p, delivering sharp and detailed images that enhance the overall viewing experience. For users looking for even greater clarity, the LS-10D is also compatible with 4K content through its advanced upscaling technology, allowing it to present finer details in high-resolution formats without losing quality.

The LS-10D employs an advanced lamp technology, producing an impressive brightness level that ensures excellent performance even in well-lit environments. This capability makes it ideal for a variety of settings, from dedicated home theaters to living rooms where ambient light cannot be controlled. Users will appreciate the projectors' reliable light source that enhances contrast and reduces the risk of color fading over time.

To further complement its impressive features, the LS-10D incorporates a range of connectivity options. This includes HDMI inputs, component video inputs, and RS-232 control, allowing for seamless integration with various sources such as Blu-ray players, gaming consoles, and home automation systems.

Additionally, the LS-10D's sleek and compact design makes it an attractive addition to any home theater setup. With its quiet operation and efficient cooling system, users can enjoy their favorite films without the distraction of fan noise.

In conclusion, the Runco LS-10D is a powerful projector that stands out for its exceptional image quality, advanced technologies, and user-friendly features. With its array of capabilities, it provides a premium home cinema experience that is sure to impress even the most discerning movie aficionados.
Top Page Image Contents