Runco Q-750D operation manual Controls and Functions, 750d at a Glance

Page 21

2. Controls and Functions

Figure 2-1shows the key Q-750d components.

Top IR Sensor

Intake Vent (on side)

Runco Logo

Focus Ring

Projection Lens

Front Bezel

Retaining

Screw

Zoom Ring

Status LED

Exhaust Vent

Front IR Sensor

Figure 2-1. Q-750d Front/Bottom/Side/Top Views

•TOP IR SENSOR

Receives infrared signals from the remote control unit.

•INTAKE VENT

Internal fans draw cool air into the projector through this vent.

•RUNCO LOGO

The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees.

•FOCUS RING

Rotate this to focus the projected image.

•PROJECTION LENS

Available in two versions: standard throw range (1.85:1 to 2.40:1) and short throw range (1.56:1 to 1.86:1).

•FRONT BEZEL RETAINING SCREW

Loosen this screw to allow removal of the decorative front bezel, which provides access to the lens shift controls (refer to Lens Shift on page 34).

•ZOOM RING

Rotate this to change the projected image size.

2.1

Q-750d at a Glance

Q-750d Series Installation/Operation Manual

5

Image 21

Contents 750d 750d/CineWide 750d/CineWide with AutoScope 750d SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures List of Figures About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories 750d at a Glance Controls and FunctionsPower Input 100 to 240 VAC Connect the Q-750d to power here 750d Rear PanelOff = Normal operation Virtual Cinema is available only on the Q-750d/CineWide or DHD Controller Front PanelDHD Controller Rear Panel DHD Controller Rear PanelInputs OutputsDHD Controller/Q-750d Remote Control 750d Remote Control UnitCursor Buttons On / OFFInformation about aspect ratios, refer to Table Menu button see below to exit the current menuAspect Ratio Selection Buttons Memory Preset Buttons169 Letbox LetterboxInstallation Remote ControlInstallation specialist Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Throw Distance Ambient LightThrow Ratios for the Q-750d Series PrimaryLens Screen Lens Only Anamorphic Minimum Maximum Floor Installation Ceiling InstallationVertical and Horizontal PositionVertical lens shift figures are for ceiling mount Possible Audio Latency for Various Input Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Installing the Optional CineWide/AutoScope Lens MountLens Motor Q-750d/CineWide with AutoScope Q-750d/CineWide with AutoScope Motor Assembly Exploded ViewRemove Projector Front Feet Q-750d with Ceiling Mount Adapters/Projector Stands Install Lens MotorAutoScope Lens Motor Installation CineWide Base Plate 750d/CineWide Installing the FixedLens base plate Do not use the mounting screws provided with the ceilingMounting the Q-750d Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting Inverted AngleConnector Panel Access Connecting the DHD Controller to the Q-750dConnections to the Q-750d and DHD Controller 11. RS-232 Connection from the DHD Controller to the Q-750d Components to the DHD Connecting SourceHdmi Source Connections See Figure ControllerDTV-Set-Top Box 13. Component Video Source ConnectionsRGB Camcorder Computer15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerAdjusting the Picture Orientation Primary Lens AdjustmentsYou must enter a passcode to access the Service menu Zoom Out FocusInstalling and Adjusting the CineWide Anamorphic Lens Anamorphic Lens Installation AdjustmentIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusService Main MenuRunco Video Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowMemory Presets Sleep Timer Sleep TimerInformation You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyCIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesModes on a given input X/y Color Gamut Values Given inputColor Saturation Hue SaturationHue Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Operation Operation 58 and ISF Day/Night Memory Presets Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionMaintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsMiscellaneous Commands Enter keyExit Return key Using Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter Specifications 750d SpecificationsQ-750d Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsDHD Controller Specifications DHD Controller SpecificationsOverall Dimensions Q-750d Overall Dimensions Q-750dOverall Dimensions Q-750d/CineWide with AutoScope Overall Dimensions Q-750d/CineWide with AutoScopeFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoComponent/ Rgbhv Video 1 S-Video Format Resolution FrequencyVideo Rate Hz MHz KHzPAL-M Page 020-0997-00 Rev. a November