Runco Q-750D operation manual Remote Control, Installation specialist

Page 29

3. Installation

Note	Installation must be performed by a qualified custom video
	installation specialist.

To install batteries in the remote control, press up on the battery cover retainer clip and lift off the cover. Install the two AAA batteries with the correct polarity and then replace the cover.

•Make sure that the battery polarities are correct when installing the batteries.

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

•Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector.

•If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

•The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.

•Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation.

3.1

Remote Control

Notes on Batteries

Notes on Remote Control Operation

Q-750d Series Installation/Operation Manual

13

Image 29

Contents 750d 750d/CineWide 750d/CineWide with AutoScope 750d SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and TroubleshootingExternal Control SpecificationsTable of Contents Xiv List of Figures List of Figures About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionFormat screen Description, Features and BenefitsOptional Accessories 750d at a Glance Controls and FunctionsOff = Normal operation Power Input 100 to 240 VAC Connect the Q-750d to power here750d Rear Panel Virtual Cinema is available only on the Q-750d/CineWide or DHD Controller Front PanelDHD Controller Rear Panel DHD Controller Rear PanelInputs OutputsDHD Controller/Q-750d Remote Control 750d Remote Control UnitCursor Buttons On / OFFInformation about aspect ratios, refer to Table Menu button see below to exit the current menuAspect Ratio Selection Buttons Memory Preset Buttons169 Letbox LetterboxInstallation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Throw Distance Ambient LightLens Screen Lens Only Anamorphic Minimum Maximum Throw Ratios for the Q-750d SeriesPrimary Floor Installation Ceiling InstallationVertical and Horizontal PositionVertical lens shift figures are for ceiling mount Possible Audio Latency for Various Input Timings Synchronization IssuesAudio/Video Input Timing Possible Audio Latency millisecondsOther Considerations Installing the Optional CineWide/AutoScope Lens MountLens Motor Q-750d/CineWide with AutoScope Q-750d/CineWide with AutoScope Motor Assembly Exploded ViewRemove Projector Front Feet Q-750d with Ceiling Mount Adapters/Projector Stands Install Lens MotorAutoScope Lens Motor Installation CineWide Base Plate 750d/CineWide Installing the FixedLens base plate Do not use the mounting screws provided with the ceilingMounting the Q-750d Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting Inverted AngleConnections to the Q-750d and DHD Controller Connector Panel AccessConnecting the DHD Controller to the Q-750d 11. RS-232 Connection from the DHD Controller to the Q-750d Components to the DHD Connecting SourceHdmi Source Connections See Figure ControllerDTV-Set-Top Box 13. Component Video Source ConnectionsRGB Camcorder Computer15. Scart Rgbs Source Connections Gaming ConsoleCamcorder Composite and S-Video Source ConnectionsConnection RS-232 ControllerAutoScope Lens Motor Connecting 12-volt Trigger Outputs to External EquipmentReceiver to the DHD Connecting an External IRConnecting to AC Power Turning on the PowerAdjusting the Picture Orientation Primary Lens AdjustmentsYou must enter a passcode to access the Service menu Zoom Out FocusIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Geometry Operation Using the On-Screen MenusRunco Video ServiceMain Menu Aspect Ratio Input SourceInput Source Aspect RatioRemote Aspect Ratio Control Description Key 169 Aspect Ratio SettingsSelect 169 to view 169 DVDs Hdtv programs in theirOverscan Remote Aspect Ratio Control Description KeyPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep TimerInformation You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians onlyCIE 1931 Chromaticity Diagram Modes on a given input Color Temperature Presets and Associated Color PointsColor Temperature Preset Associated x/y Values Color X/y Color Gamut ValuesGiven input Hue SaturationHue Saturation Copy/Paste Copied settings are not retained after a power cycleService ServiceInput Names Operation Operation 58 and ISF Day/Night Memory Presets Troubleshooting Tips Maintenance and TroubleshootingTroubleshooting Chart Symptom Possible Causes SolutionMaintenance and Troubleshooting Serial Command Syntax Port ConfigurationExternal Control Serial CommunicationsInput Selection Commands Serial CommandsPicture Adjust Commands Output Shift Commands Input Position CommandsExit Return key Miscellaneous CommandsEnter key With Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits Remote Control With Toggle Description Button Name Bit = IR Command ListRC5 Control Codes for the DHD Controller RC5 DataEnter Q-750d Specifications Specifications750d Specifications Industry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsDHD Controller Specifications DHD Controller SpecificationsOverall Dimensions Q-750d Overall Dimensions Q-750dOverall Dimensions Q-750d/CineWide with AutoScope Overall Dimensions Q-750d/CineWide with AutoScopeFormat Resolution Frequency Rate Hz MHz KHz Supported Signal Timings by InputSupported Timings Supported? √ = Yes, = NoComponent/ Rgbhv Video 1 S-Video Format Resolution FrequencyVideo Rate Hz MHz KHzPAL-M Page 020-0997-00 Rev. a November