Runco Q-750D operation manual Geometry

Page 62

Installation

Geometry:

1.Input an anamorphic cross-hatch test pattern to the projector.

2.Unscrew the Anamorphic Lens just enough to allow it to rotate freely.

3.Grasp the lens by the center ring and rotate the lens until the image is properly anamorphic:

Wrong Position

Correct Position

4.When the image geometry appears correct, tighten the Anamorphic Lens Set Screw (item #10) to secure the lens in place. (When viewed from the front, the rear opening on the anamorphic lens should appear as a tall, narrow oval.)

Focus: Finally, rotate the Focus Ring on the anamorphic
lens to fine-tune the optical focus.	S

U

C

O

F

46	Q-750d Series Installation/Operation Manual

Image 62

Contents 750d Series 750d 750d/CineWide 750d/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Maintenance and Troubleshooting OperationSpecifications External ControlTable of Contents Xiv List of Figures List of Figures Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Format screenOptional Accessories Controls and Functions 750d at a GlanceOff = Normal operation Power Input 100 to 240 VAC Connect the Q-750d to power here750d Rear Panel DHD Controller Front Panel Virtual Cinema is available only on the Q-750d/CineWide orDHD Controller Rear Panel DHD Controller Rear PanelOutputs Inputs750d Remote Control Unit DHD Controller/Q-750d Remote ControlInformation about aspect ratios, refer to Table On / OFFCursor Buttons Menu button see below to exit the current menu169 Memory Preset ButtonsAspect Ratio Selection Buttons Letbox LetterboxInstallation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Ambient Light Throw DistanceLens Screen Lens Only Anamorphic Minimum Maximum Throw Ratios for the Q-750d SeriesPrimary Vertical and Horizontal Ceiling InstallationFloor Installation PositionVertical lens shift figures are for ceiling mount Audio/Video Synchronization IssuesPossible Audio Latency for Various Input Timings Input Timing Possible Audio Latency millisecondsInstalling the Optional CineWide/AutoScope Lens Mount Other ConsiderationsQ-750d/CineWide with AutoScope Motor Assembly Exploded View Lens Motor Q-750d/CineWide with AutoScopeRemove Projector Front Feet Install Lens Motor Q-750d with Ceiling Mount Adapters/Projector StandsAutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate 750d/CineWideDo not use the mounting screws provided with the ceiling Lens base plateFloor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Q-750d AngleConnections to the Q-750d and DHD Controller Connector Panel AccessConnecting the DHD Controller to the Q-750d 11. RS-232 Connection from the DHD Controller to the Q-750d Hdmi Source Connections See Figure Connecting SourceComponents to the DHD Controller13. Component Video Source Connections DTV-Set-Top BoxComputer RGB CamcorderGaming Console 15. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens MotorConnecting an External IR Receiver to the DHDTurning on the Power Connecting to AC PowerYou must enter a passcode to access the Service menu Primary Lens AdjustmentsAdjusting the Picture Orientation Zoom Out FocusIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Time after turning on the systemInstallation Anamorphic Lens Top View Geometry Using the On-Screen Menus OperationRunco Video ServiceMain Menu Input Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in theirRemote Aspect Ratio Control Description Key OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep TimerCalibration You must enter a passcode to access the Calibration menuInformation Should be used by ISF-certified technicians onlyCIE 1931 Chromaticity Diagram Modes on a given input Color Temperature Presets and Associated Color PointsColor Temperature Preset Associated x/y Values Color X/y Color Gamut ValuesGiven input Hue SaturationHue Saturation Copied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Operation Operation 58 and ISF Day/Night Memory Presets Troubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsExit Return key Miscellaneous CommandsEnter key With Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter Q-750d Specifications Specifications750d Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications DHD Controller SpecificationsOverall Dimensions Q-750d Overall Dimensions Q-750dOverall Dimensions Q-750d/CineWide with AutoScope Overall Dimensions Q-750d/CineWide with AutoScopeSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoVideo Video 1 S-Video Format Resolution FrequencyComponent/ Rgbhv Rate Hz MHz KHzPAL-M Page 020-0997-00 Rev. a November