LG Electronics DV1000 Operation with tape Playing a tape, Getting a better picture, Auto Tracking

Operation with tape

Playing a tape

You will only be able to load and eject video cassettes when your VCR is plugged into the mains.

Your VCR may also play back recordings from NTSC tapes (on PAL TV).

Getting a better picture
When a cassette is inserted and playback started, the
automatic tracking function works to get the best
possible picture automatically. If the quality of the
recording is poor, repeatedly press	3 or 4 on the
remote control to manually adjust the	tracking until
any distortions have been removed.	Press numbered
0 on the remote control to switch automatic tracking
back on again.

Picture search will only continue for about 3 min- utes, after which your VCR will return to normal playback. During picture search, logic search, and CM Skip the sound is mute and there will be some noise streaks on the picture.

1VCR as described earlier in this book.

Turn on your TV and select the video channel for video playback.

Press POWER to turn on your VCR. Insert the video cassette into your VCR.

The video cassette should have the window side facing up and the arrow facing away from you.Make sure that you have correctly connected your

2If you load a video cassette which has had its record protection tab removed, playback of the cassette will start automatically.

AUTO TRACKING

Your VCR will automatically adjust the tracking to give the best picture quality.Press PLAY to start playing your tape.

3Press PAUSE/STEP repeatedly to advance the still picture frame by frame.

If you hold down FORWARD, the picture will be slowed down at about 1/19 times the normal

playback.

Tapes can be paused for up to 5 minutes. After 5 minutes your VCR will stop the tape to prevent damaging the tape or your VCR .

Press D or E to reduce the vertical tremble during still picture.Press PAUSE/STEP to pause a picture.

4	Press PLAY to continue	playing your tape.
	Picture search:	FORWARD or
	During playing back press either

BACKWARD to this will enable you to rapidly wind the tape (7 times normal playback speed) and see

where you are on the tape.

Logic search:

During fast forwarding or rewinding press and hold FORWARD or BACKWARD the picture will be played back at 7 times normal playback speed.

Slow motion playback,Shuttle :
5 During playing back or still picture press	F or G.

You can reach the following playback speeds.

(-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay,

7xplay)				OPERATION
To switch off the slow motion and shuttle, press the
desired function.
During slow motion and shuttle, the noise bars may
appear on the picture according to the status of
tape.
If distortions can be seen in the picture, reduce
them with		D or	E.
Press		STOP to end playback.
6 Press		EJECT.
If the end of the tape is reached, your VCR will stop
playback automatically, rewind, stop, eject the tape.
CM (Commercial Message) Skip:
This feature enables you during playback of a tape to
skip a commercial break in a few seconds, then resume
normal playback.			CM SKIP on the remote
While tape is playing press
control to skip commercial (or another programme
material).		CM SKIP to skip:
Repeatedly press
1 Press	30 seconds
2 Press	60 seconds
3 Press	90 seconds
4 Press	120 seconds
5 Press	150 seconds
6 Press	180 seconds

OPR (Optimum Picture Response)

This feature automatically improves playback picture quality by adjusting your VCR to the condition of the tape.

1Press i.

2Press 1 or 2 to select OPR.

3 Press OK.

	OFF		1	2		VCR
		Pr-12			SYS-
REC	P SET	ACMS	TIME			Dr.
	SOFTR		DATE		TEM

f OSD	SHARP	NIC	OPR
ON	16:9	OPR	i
OFF	4:3

4	Press	3 or 4 repeatedly to select:	OFF,SOFT or
	SHARP.
	Please note you may only set OPR when
	playing a tape.
5 Press		i to remove the menus.

21