LG Electronics AN110W-JD, AN110B-JD Installation and Composition, Installation Instructions

Page 12

Installing and Composition

Installation and Composition

Installation Instructions

* Don’t place the projector in the following conditions. It may cause malfunction or product damage.

Provide proper ventilation for this projector.

●The projector is equipped with ventilation holes(intake) on the bottom and ventilation holes(exhaust) on the front. do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

●Never insert materials as paper into the lower of the projector.

●Ensure good ventilation around the projector.

The distance between the projector and the ceiling or bottom should be more than 20cm/8 inches.

Place this projector in adequate temperature and humidity conditions.

●Install this projector only in a location where adequate temperature and humidity is available. (refer p.47)

Don’t place the projector where it can be covered with dust.

●This may cause overheating of the projector.

The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a nor- mal result of the manufacturing process and does not indicate a malfunction.

To display DTV programs, it is necessary to connect a DTV receiver (Set-top Box) and connect it to the projector.

If there is no input signal, the Menu will not be displayed on screen.

12

Image 12

Contents AN110B-JD AN110W-JD DLP Projector Class B digital deviceContents Safety Instructions Never touch the power plug with a wet hand Prevent dust collecting on the power plug pins or outletDo not plug too many devices into one outlet Dispose of used batteries care- fully and safelyDo not use water while cleaning the projector Only use the specified type of batteryDo not drop the projector or allow impact shock Do not place heavy objects on top of projectorPart Descriptions Main BodyControl Panel Remote Control Installing BatteriesProjector Status Indicators Service centerAccessories Remote Control Batteries size AAAOptional Extras Installation and Composition Installation InstructionsDon’t place the projector where it can be covered with dust Provide proper ventilation for this projectorBasic Operation of the Projector Projection distance based on the picture formatInstalling the projector to the wall Safety instructions on installing the wallFollow the instructions when installing this product Unplug the product before installingInstalling Wall mounting bracket Detach the productsAssemble projector with the product fixing bracket Anchors insertion position Install the wall mounting bracket on the wall Assemble the projector with the wall mounting bracket Adjusting Tilt Angle Adequate installation space from the wallAdjusting Tilt Angle Turn Selecting source mode Turning on the ProjectorTurning off the Projector Focus, Zoom, Position of the Screen Image Connecting to a Desktop PC Connecting to a Notebook PCHow to connect ConnectionConnecting to a Video Source Connecting to a DVDUse a DVD with Component 480i576i/ 480p576p/720p/1080i mode Connecting to a D-TV Set-Top Box How to connect an RGB/HDMI sourceUse a DTV receiver with DTV 480p576p/ 720p/1080i mode How to connect a Component sourceHdmi Accessories Hdmi cable is not supplied with the productHdmi Cable Hdmi to DVI Cable Adjusting Video FunctionAPC Auto Picture Control FunctionAuto Color Temperature Control Gamma FunctionColor Temperature Control Use the F, G button to make appropriate adjustmentsReset Reset to original factory value White peaking FunctionUsing ARC Function You can also use this function by using the Menu buttonSelecting Language Sleep timer turns the projector off at the preset time Flip horizontal FunctionXD Demo Auto sleep FunctionUsing Keystone function Using Blank functionPress any button to cancel the blank function Press the Keystone + or Keystone buttonLamp mode Function Selecting Blank image colorChecking Lamp time Using Still function Tilt functionPress the Still button To exit Pause, press any buttonAuto configure Function Manual configurePress the F, G button to adjust the screen condition Press the Auto buttonUsing Zoom function You are available o this function after adjusting Zoom +Screen Position How to connect external control equipment Communication Parameter SetupRS-232C Command Reference List Transmit ‘FF’ data to read status of commandCommunication Protocol Carriage ReturnPower Command2a Input Select Command2bScreen Mute Command2d Contrast Command2gBrightness Command2h Color Command2iSharpness Command2k OSD Select Command2lLow Power Command1j, Command2q Auto Configure Command1j, Command2uSupported Monitor Display InformationRGBDTV-*2 Cable type RCA to D-Sub Adaptor Computer CableMaintenance Cleaning the lensCleaning the Projector Case Last of Lamp unit replacement Be careful when replacing lampTo obtain a replacement Lamp unit Replacing the LampLift up the fixed wire knob on the lamp Replacing the LampMemo Memo Specifications Operating ConditionProjector Lamp No 3828VA0577A a