Hitachi UT42V702, UT37V702 manual Important Safety Instructions, English

Page 3

IMPORTANT SAFETY INSTRUCTIONS

SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI LCD MONITOR

Our reputation has been built on the quality, performance, and ease of service of Hitachi LCD Monitors.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your Hitachi LCD Monitor.

Please fill out your warranty card and mail it to Hitachi. This will enable Hitachi to notify you promptly in the improbable event that a safety problem should be discovered in your product model. Model and serial numbers are indicated on back side and right side of the LCD Monitor.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to a person.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ENGLISH

READ BEFORE OPERATING EQUIPMENT Follow all warnings and instructions marked on this LCD Monitor.

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use the attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Monitors and Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.

16.Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

17.An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.

18.If an outside antenna is connected to the receiver and the monitor be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead- in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

NOTE

To the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-44 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

2

Image 3
Contents UltraVision Hdtv Monitors Contents English Important Safety InstructionsModifications Important Safety InstructionsLead/Mercury Notice Declaration of ConformityTrademark Credits FeaturesIntroduction About This ManualDo not remove covers, or modify the product Safety PrecautionsExplanation of the Symbols Other SymbolsSafety Precautions Do not pull the cord when you unplug the power cord Do not install the unit near medical devicesConnect the power plug securely Do not handle the power cord with wet handsCleaning and Maintenance Securing to a table Safety Precautions Main Unit InstallationFasten the fastening strap to a table using Anti-tumble MeasuresSafety Precautions Child Safety Notice Tune Into SafetyRemove the Stand Base from the Monitor Safety Precautions Wall Mount SetupSpecification is shown below About the InstallationSafety Precautions Floor Stand Setup Install the Monitor on the Floor StandTabletop stand Supplied Accessories including option Quick Start GuideConnection 18 ~ Control Power OnQuick Start Guide Insert the Batteries into the RemoteRear Panel Component NamesMain Unit Front PanelComponent Names Remote Control Install the batteries Remote Control Battery InstallationHandling the Remote Control Open the battery compartment coverConnect your Equipment to the Monitor Connect Power Cord to the Rear PanelConnecting to Equipment Having Hdmi or DVI Output Terminals ConnectionGame Mode Connecting to Equipment Having Video Output TerminalsConnection Connect your Equipment to the Monitor Connecting to a PC Attach Cushion, Secure with Clamps and Fit Terminal CoverAttach the supplied cushion around the Hdmi cable Fit the terminal cover onto the monitor Connect the Power Plug into the Wall SocketSecure the Hdmi cable and power cord with clamps ConnectionBasic Operation Power On/OffTo turn On the power to the unit To turn Off the power to the unitMute Basic Operation Volume Up/DownInput Signal Screen Display Basic Operation Input Switching to Hdmi and RGBRemote Control Backlight Feature Setup OperationHow to Use the Remote to Control your External Devices Setup Example Hitachi Cable Box with precodePrecoded SET-TOP-BOX/SATELLITE buttons Exclusive TV mode Monitor buttonsMY Cable BOX Code is Precoded Cable BOX buttonsMY DVD Player Code is MY VCR/PVR Code is Precoded DVD buttonsPrecoded VCR/PVR buttons Exclusive TV mode buttons Code isPrecoded AVR buttons Cable Brand Setup Operation Remote Control CodesEnglish Basic Operation How to Use the On-Screen Display OSD SystemHow to set Language Select LanguageMenu Setup Operation Main Menu ListSetting Picture Adjustment Setup Operation Watching Images from HDMI/Composite Input3D Color Management Selected Items Setup hint Deep ColorContrast Mode Color Temp. AdjustCross Color NR Reducing NoiseMaking the Moving Image Smooth Film ModeColor System Advanced SettingSelected Items Setup hint Video Power Save RGB InputPicture Menu Setup Operation Viewing Images from a PCSelected Items Setup hint Frequency Display Setup MenuAuto Adjust Clock PhaseDisplay Aspect Aspect SwitchingHDMI/Composite Signal Input FunctionsRGB Signal Input Display Aspect Functions Aspect SwitchingHDMI/Composite Signal Input Position Adjustment Using a wide-screen monitorFunctions Power Save Mode When HDMI/Composite Input is SelectedWhen RGB Input is Selected About LCD Display Technology TroubleshootingWhen the Following Messages Appear on the Screen Symptom and ChecklistTroubleshooting Symptom and Checklist Symptoms46 ~ Try Auto Adjust Stripes appear and some Specification Product SpecificationsApprox inches measured diagonal Pin Input signal Product Specifications Signal InputRGB terminal D-sub 15 pin connector Hdmi connector pin specificationsFrequency Remarks Product Specifications Recommended Signal ListWith Hdmi input With RGB inputProduct Specifications Dimensions Product Specifications Dimensions Product Specifications Dimensions Service Information Operational, hook up Warranty questions for your productCustomer Record Visit our websiteONLand register your product online Limited WarrantyConditions of Hitachi Limited Warranty HitachiEND User License Agreement for Hitachi Software END User License Agreement for Hitachi Software