Hitachi P50V701 Remote Control for Set-Top-Box/Satellite Receiver Functions, SET-TOP-BOX Code is

Page 37

The Remote Control for Set-Top-Box/Satellite Receiver Functions

OPERATING THE PRECODED FUNCTION FOR YOUR SET-TOP-BOX/SATELLITE RECEIVER.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set- top-box/satellite systems (refer to pages 41-42 for pre- codes).

1.Turn ON your set-top-box/satellite systems.

2.To switch to set-top-box/satellite (SAT) pre-coded mode, use the SOURCE SELECT button on the remote control to position the LED light to the corresponding selection SAT/CBL.

3.Hold down the SOURCE SELECT button on the remote and enter the four digit preset code that matches your set- top-box/satellite receiver as shown on page 41-42. Release the SOURCE SELECT button. The indicator light will flash 3 times if the code was accepted.

4.Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite receiver when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your set-top-box/satellite receiver. If the set-top- box/satellite receiver does not turn off, try a different four digit preset code.

5.The remote will now control your set-top-box/ satellite receiver.

NOTE: 1. If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top-box/ satellite receiver code has not been precoded into the remote.

2.In the unlikely event that your set-top- box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the

remote control. After replacing the batteries repeat the entire programming procedure as stated above.

￿

￿

￿

 

￿

￿

￿

￿

 

￿

 

￿

 

￿￿

￿￿

￿

￿PRECODED SET-TOP-BOX/SATELLITE RECEIVER buttons

These buttons transmit the chosen pre-coded set-top-box/satellite codes :

-Power

-Cursor & Select

-Number PAD

-Menu

-Info

-Enter, Dash

-Exit

-Channel Up & Down

 

-Guide

-Last CH

 

￿EXCLUSIVE TV buttons

These buttons are for operating the TV :

-Day/Night

-CC

-Mute

-Aspect

-Vol Up & Down

-Inputs (Only if

-PIP

-Pause

programmed, refer

MY Satellite RECEIVER/

to page 40).

 

SET-TOP-BOX CODE IS:

 

NOTE: Refer to instruction manual of the Set-Top- Box/Satellite Receiver for operation of the buttons exclusively for the Set-Top- Box/Satellite Receiver.

The Remote Control

37

Image 37
Contents Plasma Television Read Before Operating Equipment Important Safety InstructionsPublic viewing of copyrighted material Power sourcePrevention of screen damages Lead NoticeRemote Control Battery Installation and Replacement AccessoriesFor U.S. models Connect Power Swivel Cable How To Set Up Your New Hitachi Plasma TelevisionAntenna LocationAC Cord Step Setting for Wall MountingViewing When both VHF and UHF antennas are ConnectedAntenna Connections to Rear Jack Panel VHF 75-Ohm antenna/CATV Cable TVTime use Hook-up Cables and Connectors CBL Quick Reference Remote Control Buttons and FunctionsSAT Front Panel Controls Remote Control sensor Power light indicatorLearning AV NET sensor INPUT-FRONT JacksIR Out / G-LINKTM Rear Panel ConnectionsMonitor OUT & Audio OUT Do not insert a Pcmcia card into the CableCARD slot CableCARD SlotConnecting Hdmi signal Connecting External Video SourcesConnecting DVI signal Front Input PanelFront Input Panel Before Operating External Video SourceDigital Tips on Rear Panel Connections Installation RecommendationConnecting AN S-VIDEO and Stereo Audio Source to Input DVI to Hdmi Input Hdmi inputConnecting External Audio/Video Devices Connecting Monitor OUT Connecting AN External Audio AmplifierSET LINKTMconnections are available on both IR OUT terminals Addition to controlling all the functions on your Remote ControlMode Indicator How to Use the Remote to Control Your TVPause button DAY/NIGHT buttonExpanded Standard ZOOM1/ZOOM2Standard Digital Channels Analog ChannelsHdmi Photo Input Cursor PADRotate Channel SELECTOR/FAVORITE Channel WhitePOP Mode PICTURE-IN-PICTURE Split Mode PICTURE-IN-PICTUREPicture-In-Picture PIP PIP buttonHdmi PIP Mode PICTURE-IN-PICTUREMain Freeze Between Freeze modes Main Freeze, SplitSplit Freeze Strobe FreezeOperating the Precoded Function for Your Cable BOX Remote Control for Cable Box FunctionsPrecoded Cable BOX buttons Exclusive TV buttonsPrecoded SET-TOP-BOX/SATELLITE Receiver buttons Remote Control for Set-Top-Box/Satellite Receiver FunctionsMY Satellite Receiver SET-TOP-BOX Code isOperating the Precoded Function for Your DVD Player Remote Control for DVD FunctionsPrecoded DVD Buttons MY DVD Player Code isPrecoded VCR/PVR Buttons Remote for VCR/PVR FunctionsMY VCR/PVR Code is Input Access How to Use the Source Select ButtonCable Brand Codes Remote Control CodesPVR Brand Video On-Screen DisplayAudio Video Contrast Mode Color TemperatureAuto Movie Mode Black EnhancementAspect Black Side PanelAuto Aspect ModeReset Video Settings Smooth Original Treble AudioBass BalancePerfect Volume Auto Noise CancelAudio Source Internal SpeakersTV Guide On Screen Setup ProcedureTV Guide On Screen TV Guide On Screen Channel Manager Signal MeterAuto Channel Scan Channel List Locks Change Access CodeEngage Lock Motion Picture Ratings Table Movie RatingsTV Parental Guide Ratings Table TV RatingsCanadian Ratings English Table Canadian Ratings EngCanadian Ratings French Chart Dtvcc Alternate Ratings Example OnlySet The Clock TimersSet Day/Night Timer Set Sleep Timer300 Setup Automatic Power Saving Image PowerSet The Screen Saver OptionAuto Set The InputsOff Set AV NetPress the Select button to start the Setup Wizard AV NET Setup Wizard Example A/V Receiver SetupAV Net Setup Wizard Device Settings AV NET Setup Wizard Example DVD SetupLearning Mode SetupAV Net Setup Wizard Custom Settings Learning Mode Example CUSTOM/DVD 3 Setup DVD3 Other Brand Remote Control Side View AV Net Learning Mode Distance SpecificationSet The Closed Captions Caption ModeCaption Display Analog CaptionsIR Out IR Passthru Distance Specification CableCARD / CableCARD Services Things to Check When UsingInsert MMC/SD Card Upgrade NOWLocked Troubleshooting Equipment Care and TroubleshootingSwitch ON/OFF Switch once Switch againReception Problems FCC Information Useful InfoLink TM InputsRear View, Use as Reference for Wall Mount Bracket Set DimensionsDigital Media Division Home Electronics DivisionUseful Information END User License Agreement for Hitachi DTV Software End User License Agreement for Hitachi DTV SoftwareOperating System License Information Software Module Applicable Software LicenseGNU General Public License Version 2, June End User License Agreement for Operating System SoftwareNo Warranty END of Terms and Conditions Preamble GNU Lesser General Public License Version 2.1, February179 End User License Agreement for Operating System Softwaree Agreements Appendixes Aspect SpecificationsAppendix a Appendix a Index