Hitachi C43-FL9000, C52-WD9000 Addenda, Guide to simple problem solving, Accessories

Page 53

ADDENDA

A guide to simple problem solving

Before calling up the service personnel, please check the following chart for a possible cause to the problem you are encountering.

Symptom

Possible causes

No picture,no sound,power/standby indicator is OFF.

The power cord is not plugged in.

No picture,no sound,power/standby indicator is ON.

The TV is in standby mode.

No sound

The volume control is set to minimum.

 

The Speaker option in Setup menu is set to Off.

Twist image and poor sound

The antenna signal is too weak or too strong.

 

The TV is not tuned correctly.

Poor brightness, color or tint

The contrast, brightness, color or tint may be misadjusted.

Snowy picture

Interference from motorcycles, high-tension line, electric hair drier,

 

personal computer or radio station.

Ghosts

Check the direction, height or position of the antenna.

No color

The antenna signal is too weak.

 

Color System or Sound System is not set properly.

Remote controller does not work.

The batteries in the remote controller may be exhausted.

 

The batteries may be improperly installed.

 

There is obstruction between the remote controller and the TV.

 

 

HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal power surges.

If your TV appears A LOSS OF POWER, please follow the following procedure:

1. Press the POWER button once.

2.If there is still no power, wait for 30 seconds and press the POWER button again.

3.If there is still no power, unplug the power cord from the wall outlet. Wait for 30 seconds and plug the power cord in. Press the POWER button again.

The protective technology should provide you years of lasting entertainment from your HITACHI Projection Television.

The following phenomena are not failures:

1 The picture takes a while to appear on the screen when the power is on.

2The cabinet clicks. The clicking is a creaking sound produced when the cabinet expands or contracts due to changes in temperature.

3Unevenness in color sometimes develops in part of the screen. Such unevenness in color may occur depending upon the nature or setting of the picture. The proper color may be restored by reducing the contrast or adjusting other settings.

4The TV set can generate sound distortion in external devices such as a radio. Please place the radio equipment away from the TV set.

Accessories

No.

 

Description

 

Quantity

 

C43-FL9000

 

C52-WD9000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

Instruction manual

1

 

Yes

 

Yes

 

 

 

 

 

 

 

 

 

2

 

Remote control unit (CLE-962)

1

 

Yes

 

Yes

 

 

 

 

 

 

 

 

 

3

 

Battery (For CLE-962)

2

 

Yes

 

Yes

 

 

 

 

 

 

 

 

 

4

 

Caster holder

4

 

Yes

 

Yes

 

 

 

 

 

 

 

 

 

5

 

Antenna adapter

1

 

Yes

 

Yes

53

Image 53
Contents /  Contents Forbidden actions Required actions Safety TipsAvoid any kind of impact to your television Cleaning Precautions when movingMoisture Condensation Best spot for viewing Before Using this Projection Color TVLocation Precautions when connecting the antenna Connect the power cord and the antennaPrecautions when using the batteries Precautions when using the remote control unitControl panel and side panel Functional PARTSFunctional PARTS Terminals Functional PartsRear panel On the remote control unit To Turn on the Power Power on/offWhen the SET is AT Standby To Turn OFF the PowerInstructions for operating menu Getting StartedMenu Selecting the on-screen display languageEasy Preset Picture Menu ON-SCREEN Display Menu Picture MenuSet to On, you can adjust and balance their individual When the Color Manager option shown on the right isIf the option of Reset was selected and press the Enter Top right to select the Color Manager option, then pressAudio Menu ON-SCREEN Display Menu Audio MenuTimer Menu ON-SCREEN Display Menu Timer MenuOff Timer On TimerAuto P.Size option ON-SCREEN Display Menu Function MenuFunction Menu SDQGHG 3UHVHW ON-SCREEN Display Menu Setup MenuPress Cursor buttons to select the Program Press the Ÿ ź cursor buttons to select the Sound System 5.5, 6.0 or 6.5 Note Here the unit MHz is omittedTV/VIDEO AntennaAV5 PAL, SECAM, NTSC4.43 or NTSC3.58LQH7XQLQJ 3URJFKDQJH  Select the Auto Mute option as shown on the right Remarks Auto LinkSpeaker Audio Out ON-SCREEN Diplay Menu Setup MenuText Language West EuropeTo save the adjusted data and exit from adjustment mode Convergence AdjustmentMulti PIC Multi PictureSplit UHHH 6WLOO 5HVHW  6HOHFW 6HW 5HWXUQ Multi Picture $9 Multi Picture CH Surf CH Surf FunctionMode Strobe function is as shown below Teletext Remark Other Functions169 TV P.SizeSize 169Zoom Expanded 43Zoom1 43Zoom2169Zoom Or Expanded mode16 9Zoom 169 169Zoom Auto P.SizeExpanded 43Zoom1 Expanded 43Zoom1 43Zoom2Recall Cancel Recall ModeRecall Recall IndexRecall button TV/VIDEO buttonCH I/II button Size buttonINPUT2 HD Signal Through ModeTypical connection of video camera, VCR, etc Connection with Other EquipmentJacks and connections of side panel Typical connection of rear panel Connection with Other EQUIPMENTJacks and connections of rear panel Hdmi Input About HdmiRear panel Typical connection of79$6&175VIDEO,PB/CB,PR/CR About the jacks and connections of rear panelAddenda Guide to simple problem solvingAccessories ADDENDA Specifications