Crown XLS 1000 Manual: Setup and Operation Guide for XLS Series Amplifiers
Page 4

XLS Series Power Amplifi ers

Get Started

Stereo Bypass Mode

This is the default mode the amplifi er is set to from the factory. The amplifi er is confi gured for stereo mode with the PureBand™ Crossover System Bypassed.

1.Connect Left/Right signal source to Channel 1 and Channel 2 using either the XLR, ¼ Inch, or RCA connectors.

2. Connect a speaker to each channel output using Speakon®, Banana Plugs, or bare wire.

Bridge-Mono Mode

Bridge-Mono Mode delivers the power of both amp channels into a single 8 or 4 ohm load.

Before you get started ensure that you:

1. Connect signal source to Channel 1 only using either the XLR, ¼ Inch, or RCA connectors.

2. Connect the speaker as shown.

a. If using the binding post outputs, connect the positive terminal of the speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.

b. If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.

Follow these quick steps to confi gure the amplifi er for “Bridge Mode”:

1.Hold the “Mode/Menu” button down for 3 sec until the LCD screen displays “Amp Mode <More>”.

2.Press the “Mode/Menu” button to begin confi guring the Amp Mode.

3.Press the “Next” button until the LCD screen reads “Mode: Bridge”.

4.Press the “Mode/Menu” button to confi rm your selection.

5.Now press the “Next” button until the LCD screen displays “Bypass”. Press the “Mode/Menu” button to confi rm your selection. The LCD screen should now read “Bridge Bypass”.

Crossover Mode

When using the “Crossover Mode”, the amplifi er is confi gured to use a LowPass

Filter on Channel 1 and a HighPass Filter on Channel 2.

Before you get started ensure that you:

1.Connect signal source to Channel 1 only using either the XLR, ¼ Inch, or RCA connectors.

2. Connect a speaker to each channel output using Speakon®, Banana Plugs, or bare wire.

Follow these quick steps to confi gure the amplifi er for “Crossover Mode”:

1.Hold the “Mode/Menu” button down for 3 sec until the LCD screen displays “Amp Mode <More>”.

2. Press the “Mode/Menu” button to begin confi guring the Amp Mode.

3. Press the “Next” button until the LCD screen displays “Input Y”. Now press the “Mode/Menu” button to confi rm.

4.Now press the “Next” button until the LCD screen displays “XOVER” and press the “Mode/Menu” button to confi rm.

5.Now use the “Previous” or “Next” button to select your desired crossover point.

6.Once you have selected your crossover point, press the “Mode/Menu” button to confi rm your selection. The LCD screen should now read “Input Y XOVER”.

page 4

Operation Manual

Page 3 Page 5
Image 4
Page 3 Page 5
Contents XLS Important Safety Instructions XLS Series amplifi ers require Class 2 output wiringDeclaration of Conformity Stereo Bypass Mode Bridge-Mono ModeCrossover Mode Get StartedHighPass Mode LowPass ModeHow to Use This Manual FeaturesWelcome Back Panel Features Front Panel FeaturesRCA Phono Inputs PureBand Crossover System Integrated Processing FeaturesPeakX Limiters XLS Serie Bedienungsanleitung Einrichtung Stereo Bypass-ModusBridge-Mono-Modus Crossover-ModusHochpass-Modus Tiefpass-ModusEigenschaften Herzlich WillkommenVerwendung dieses Handbuchs Funktionen der Frontplatte Funktionen der RückplatteBuchsen der Schraubklemmenausgänge Symmetrische XLR-EingängeIntegrierte Verarbeitungsfunktionen PureBand Crossover-SystemPeakX-Limiter Crossover-Punkte stehen zur AuswahlSerie XLS Manual de Operación Comenzar Modo Estéreo BypassModo Mono-Puente Modo CrossoverModo HighPass Modo LowPassCaracterísticas BienvenidoCómo Utilizar este Manual Funciones del Panel Frontal Funciones del Panel TraseroSistema PureBand Crossover Funciones del Proceso IntegradoLimitadores PeakX Manuel dutilisation de la série XLS Mode Stereo Bypass / neutralisation de la stéréo Mode Bridge-Mono Pont MonoMode Crossover CommencezMode HighPass Mode LowPassCaractéristiques BienvenueComment se servir de ce manuel Fonctions du panneau arrière Fonctions du panneau avantPrise d’alimenta tion CA Système crossover PureBand Fonctions du procédé intégréLimiteurs de pics XLS Specifications Weight Input/OutputProtection ConstructionService Worldwide ServiceUS and Canada Service Service at a US or Canada Service Center Factory ServicePacking Instructions Payment of Non-Warranty RepairsEstimate Approval Warranty United States & Canada Summary of WarrantyWarranty Worldwide Except USA & Canada Crown Audio, Inc IT8000, CDi1000, PCC16Page Crown Audio Factory Service Information Type of credit card MasterCard Visa American ExpressCard # Exp. date *Card ID # Name on credit card Billing address of credit cardPage XLS Series Power Amplifi ers
Top Page Image Contents