These operations are accessible by remote control.
Some may also be accessible by controls on the main unit.
Initial Setup
This section will guide you through the unit’s initial setting which includes selecting a language for your
Before you begin:
Make sure the unit is connected to antenna or cable.
1 After making all the necessary connections, press
to turn on the unit.
•It may take a few moments to turn on the unit for the first time.
•[Initial Setup] menu appears automatically after the unit is turned on.
2 Use ▲/▼ to select the
3 Use ▲/▼ to select [Antenna] for TV channels or [Cable] for CATV channels, then press OK.
Initial Setup
Make sure the antenna is connected to ''ANT. IN'' jack. | Antenna | |
Select your signal source. |
| |
| Cable | |
|
| |
|
| Skip |
Antenna | Or |
|
Cable |
| |
ANT.IN |
| |
|
| |
Select | OK OK | BACK Back | MENU Skip |
•[Autoprogram] will begin.
Initial Setup
Please wait while the system is scanning for channels. Auto programming may take more than 20 minutes to complete.
0%
Digital channels | 0 ch |
|
|
|
|
|
|
|
|
|
|
Analog channels | 0 ch |
|
|
|
|
|
|
MENU Skip
|
|
|
|
|
|
|
|
|
|
| English |
| |||
4 |
| Select “Retail” or “Home” for your location. |
|
|
|
|
|
|
| INTRODUCTION | |||||
| Use ◄/► to select the desired location setting, then |
|
| ||||||||||||
|
| press OK. |
|
|
|
|
|
|
|
|
|
| |||
|
| Initial Setup |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| PREPARATION | |
|
|
|
| Select |
|
|
| OK OK |
|
|
|
|
|
| |
|
|
|
| Retail |
|
|
| Home |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • Select [Retail] store, the unit will be set up with |
|
|
| ||||||||||
|
|
| |||||||||||||
|
| predefined setting for retail displays. In this setting, the |
| WATCHING | |||||||||||
|
| efficiency for home setting and it can be adjusted |
| ||||||||||||
|
| power consumption may possibly exceed the limited |
|
| |||||||||||
|
| requirement of the ENERGY STAR® qualification. |
|
| |||||||||||
|
| • Select [Home], the unit is set to maximize the energy |
|
| |||||||||||
|
| through a choice of picture and sound quality according |
| TV | |||||||||||
|
| to your preference. |
|
|
|
|
|
|
|
|
|
| |||
|
| • When the initial setup is completed, the lowest |
|
| |||||||||||
|
| OPTIONAL | |||||||||||||
|
| memorized channel with the confirmation message of |
| ||||||||||||
|
| the location setting will be displayed on the TV screen. |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
Note |
|
|
|
|
|
|
|
|
| SETTING | |||||
• If you are not receiving a signal from your cable service, contact the Cable |
| ||||||||||||||
|
| ||||||||||||||
| provider. |
|
|
|
|
|
|
|
|
|
| ||||
• If you press | or MENU during autoprogram, this setting will be canceled. |
|
| ||||||||||||
• The initial | autoprogram function can be executed for either [Antenna] or |
|
| ||||||||||||
| [Cable] only once. When you change the connection (Antenna / Cable), |
| TROUBLESHOOTING | ||||||||||||
|
|
| |||||||||||||
| set [Autoprogram] again. ➠ p.19 |
|
|
|
|
|
|
|
|
|
| ||||
• If there is no signal input from the antenna terminal and no operation for |
|
| |||||||||||||
| several seconds after you turn on the unit, [Helpful Hints] appears. Follow |
|
| ||||||||||||
| the instructions listed on the TV screen. |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| Initial Setup |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| No channel is registered. |
|
|
|
| Retry |
|
|
| |||||
|
|
|
|
|
| Later |
|
|
|
| |||||
|
| Try Autoprogram again? |
|
|
|
|
|
| INFORMATION | ||||||
|
| Verify that you have a cable connected to the "ANT. IN" jack on the back |
|
|
|
|
| ||||||||
|
| of the TV, the channel installation process searches this connection. If |
|
|
|
| |||||||||
|
| you are using a cable or satellite box, please confirm the input which |
|
|
|
| |||||||||
|
| you have connected the box and press "SOURCE" key on the remote |
|
|
|
| |||||||||
|
| control to select the appropriate source input. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
| Select | OK OK |
| MENU Skip |
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•You must set [Home] in step 4. Otherwise, [Picture] and [Sound] settings you adjusted will not be memorized after the unit goes to the standby mode.
After an initial setup is completed...
• If you want to scan the channels automatically again.
[Autoprogram] | ➠ p.19 |
•You can add the desired cable and analog channels unmemorized by autoprogram.
[Add Channels] | ➠ p.20 |
•If you want to change to another language. [Language Selection] ➠ p.21
•If you want to change the location setting.
[Location] | ➠ p.30 |
15
EN