Read before operating equipment

English

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any of the ventilation openings.

Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong.The wide blade or third prong are provided for your safety.When the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories speciﬁed by the manufacturer.

12.Use only with a cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the appara- tus.When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when un- used for long periods of time.

14.Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the appara- tus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Damage Requiring Service - The appliance should be serviced by qualiﬁed service personnel when:

A.The power supply cord or the plug has been damaged;

B.Objects have fallen, or liquid has been spilled into the appliance;

C.The appliance has been exposed to rain

D.The appliance does not appear to operate normally or exhibits a marked change in performance;

E.The appliance has been dropped, or the enclosure damaged.

16.Tilt/Stability - All televisions must comply with recommended international global safety standards for tilt

and stability properties of its cabinet design.

•Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product.

•Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.

17.Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

18.Power Lines - An outdoor antenna should be located away from power lines.

19.Outdoor Antenna Grounding - If an outside antenna

is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges.

Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, ground- ing of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure below.

20.Object and Liquid Entry - Care should be taken so

that objects do not fall and liquids are not spilled into the enclosure through openings.

21.Battery Usage CAUTION - To prevent battery

leakage that may result in bodily injury, property damage, or damage to the unit:

•Install all batteries correctly, with + and - aligned as marked on the unit.

•Do not mix batteries (old and new or carbon and alkaline, etc.).

•Remove batteries when the unit is not used for a long time.

Note to the CATV system installer : This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding as per NEC - National Electric Code

GROUND CLAMP	ANTENNA LEAD IN WIRE

	ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
	GROUNDING CONDUCTORS (NEC SECTION 810-21)
	GROUND CLAMPS
ELECTRIC SERVICE EQUIPMENT	POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)