Magnavox TB100MG9 owner manual Initial Setup Setup Wizard, Appropriate Viewing Channel

Page 13

Initial Setup (Setup Wizard)

Initial Setup

Ajùste inicial

1 Press [STANDBY-ON] on the remote control to activate the STB.

Presione [STANDBY-ON] en el mando a distancia para activar el STB.

lights up in green

se vuelve verde

2Turn on the TV, and select the viewing channel (ch3 or external input channel) on your TV. (Refer to your TV’s manual.)

Encienda el TV, y seleccione el canal que quiera ver (canal 3 o uno de entrada externo) en su TV. (Véase el manual del TV.)

2

1

Appropriate Viewing Channel

Configuración apropiada de el Canal de Visión

Viewing

STB

Cable Box

DVD or VCR

Connection

 

 

 

A (p.10)

“CH3”

-

-

B (p.10)

External input channel

-

-

Canal de entrada externo

 

 

 

C (p.11)

External input channel

Ch3

-

Canal de entrada externo

 

 

 

D (p.12)

“CH3”

-

External input channel

Canal de entrada externo

 

 

 

If your TV’s ch3 is already occupied, select ch4, and set the STB’s output channel to ch4. You can switch ch3 / ch4 by holding [SETUP] down over 3 seconds.

Si el c3 de su TV ya está ocupado, seleccione el c4 y luego ajuste el canal de salida del STB a c4. Puede alternar entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos.

”SETUP WIZARD” screen automatically appears.

Follow the directions shown on the TV screen to set the each setting.

13

Initial Setup (Setup Wizard)

EN

Image 13
Contents TB100MG9 Risk of Electric Shock Do not Open Before UsingInsert Important Copyright Information PrecautionsB l e o f C o n t e n t s Before Using Advanced OperationOverview Installing Batteries AccessoriesInformation on Digital Broadcasting Location of Controls Remote ControlFront Panel Remote control sensor Power indicatorRear Panel Video OUT jack yellowConnecting to a TV with A/V Jacks Connecting to a TV without A/V JacksConnections White red YellowWhite Connecting to a Cable Box OptionalRed EllowRed yellow Connecting to Other DevicesInitial Setup Initial Setup Setup WizardPress STANDBY-ON on the remote control to activate the STB Appropriate Viewing ChannelSelect the language using K / L, then press OK Select Continue using s / B, then press OKSelect your time zone using K / L, then press OK Select Autoscan using K / L, then press OKSelecting Channels on the STB Basic OperationAbout Sub-channel Broadcasting Enter the main channel numberPress Audio repeatedly To cancel still modePress Still Choosing Audio LanguagePress Display Select the desired program using s / BPress EPG while watching TV Channel BannerSelect ADD/ Delete using K / L, then press OK Press SetupAdvanced Operation Autoscan Receiving ChannelsSelect Delete using K / L, then press OK Press Setup to exitPress OK again to add the channel to the channel map AddSelecting Display Mode Adjusting AntennaPress Setup Select Detail using K / L, then press OK SelectDISPLAY MODEusing K / L, then press OKSetting the Time Zone and D.S.T Daylight Saving Time Information on Display ModePress Setup Select Time using K / L , then press OK Select Time Zone using K / L , then press OKSelect on or OFF using s / B , then press OK Select D.S.T using K / L , then press OKEnter the password using the Number buttons Chip OptionsSelect the desired rating using Select the desired rating type using K / L , then press OKThen press OK repeatedly to switch between view and block Mpaa RatingEnter the new 4-digit password using the Number buttons Select NEW Password using K / L , then press OKSelect Manual using K / L , then press OK Press Setup Select Detail using K / L , then press OKSelect Closed Caption using K / L , then press OK Closed Caption OptionsSelect desired amount of time using K / L , then press OK Auto Power DownMethod 1 Método Viewing Analog TVSelect CH3 in RF OUT menu Select ch3 on your TVSelect RF Through in RF OUT Method 2 MétodoSelect the desired channel on your TV Press STANDBY-ON to activate the STBUsing Setup to Switch RF OUT Setting Setting RF OUTSelect RF OUT using K / L, then press OK Select the desired setting using K / L, then press OKOthers TroubleshootingSpecifications Customer Service Tel Limited Warranty