Magnavox TB100MG9 Advanced Operation, Autoscan Receiving Channels, Adding/Deleting Channels

Page 18

Advanced Operation

Autoscan

(Receiving Channels)

Autoscan receives available digital channels and stores them in a channel map.

CAUTION:

•If autoscan is skipped, digital channels may not be received correctly.

1 Press [SETUP].

2Select “CHANNEL” using [ K / L], then press [OK].

3Select “AUTOSCAN” using [ K / L], then press [OK].

CHANNEL

EXIT

ADD/DELETE

CHANNEL

ANTENNA

TIME

AUTOSCAN

DETAIL

RF OUT

INITIAL

4Select “AUTOSCAN” using [ K / L], then press [OK].

AUTOSCAN

EXIT

AUTOSCAN will rescan all channels.

To cancel during scanning:

Press [SETUP] or [OK].

NOTE:

•If canceled, some channels not yet scanned may not be received. We recommend completing autoscan.

•When you want to completely refresh the channel map, delete all the channels, then do the autoscan again. See “Adding/Deleting Channels” on this page for details.

When “NO SIGNAL” appears on the TV screen:

Verify the antenna connection, then scan again.

The STB tunes in channel 2-1 and “NO SIGNAL” appears if the STB could not receive any channels.

Adding/Deleting Channels

Add or delete desired channels in the channel map.

CAUTION:

•You cannot recover the deleted channels once they are deleted unless you perform the autoscan again.

1 Press [SETUP].

2 Select “CHANNEL” using [ K / L],

CHANNEL

This may take a while to complete.

then press [OK].

TIME		BACK
DETAIL		AUTOSCAN
INITIAL
INITIAL

AUTOSCAN

The system is now scanning.



12%			Channel Found

	EXIT

•STB starts receiving available digital channels and stores them in the channel map.

•When the scanning is complete, “AUTOSCAN COMPLETED” will be indicated.

•After autoscan is complete, use [CH K / L] to verify whether STB is receiving channels properly.

SETUP

	EXIT		ADD/DELETE
	CHANNEL
			ANTENNA
	TIME
			AUTOSCAN

	DETAIL		RF OUT
	INITIAL

3Select “ADD/ DELETE” using [ K / L], then press [OK].

CHANNEL

EXIT
CHANNEL		ADD/DELETE
		ANTENNA

TIME		AUTOSCAN

DETAIL		RF OUT
INITIAL

18

EN

Image 18

Contents TB100MG9 Before Using Risk of Electric Shock Do not OpenInsert Precautions Important Copyright InformationBefore Using Advanced Operation B l e o f C o n t e n t sOverview Accessories Installing BatteriesInformation on Digital Broadcasting Remote Control Location of ControlsRear Panel Remote control sensor Power indicatorFront Panel Video OUT jack yellowConnections Connecting to a TV without A/V JacksConnecting to a TV with A/V Jacks White red YellowRed Connecting to a Cable Box OptionalWhite EllowConnecting to Other Devices Red yellowPress STANDBY-ON on the remote control to activate the STB Initial Setup Setup WizardInitial Setup Appropriate Viewing ChannelSelect your time zone using K / L, then press OK Select Continue using s / B, then press OKSelect the language using K / L, then press OK Select Autoscan using K / L, then press OKAbout Sub-channel Broadcasting Basic OperationSelecting Channels on the STB Enter the main channel numberPress Still To cancel still modePress Audio repeatedly Choosing Audio LanguagePress EPG while watching TV Select the desired program using s / BPress Display Channel BannerAdvanced Operation Press SetupSelect ADD/ Delete using K / L, then press OK Autoscan Receiving ChannelsPress OK again to add the channel to the channel map Press Setup to exitSelect Delete using K / L, then press OK AddPress Setup Select Detail using K / L, then press OK Adjusting AntennaSelecting Display Mode SelectDISPLAY MODEusing K / L, then press OKPress Setup Select Time using K / L , then press OK Information on Display ModeSetting the Time Zone and D.S.T Daylight Saving Time Select Time Zone using K / L , then press OKEnter the password using the Number buttons Select D.S.T using K / L , then press OKSelect on or OFF using s / B , then press OK Chip OptionsThen press OK repeatedly to switch between view and block Select the desired rating type using K / L , then press OKSelect the desired rating using Mpaa RatingSelect NEW Password using K / L , then press OK Enter the new 4-digit password using the Number buttonsSelect Closed Caption using K / L , then press OK Press Setup Select Detail using K / L , then press OKSelect Manual using K / L , then press OK Closed Caption OptionsAuto Power Down Select desired amount of time using K / L , then press OKSelect CH3 in RF OUT menu Viewing Analog TVMethod 1 Método Select ch3 on your TVSelect the desired channel on your TV Method 2 MétodoSelect RF Through in RF OUT Press STANDBY-ON to activate the STBSelect RF OUT using K / L, then press OK Setting RF OUTUsing Setup to Switch RF OUT Setting Select the desired setting using K / L, then press OKTroubleshooting OthersSpecifications Limited Warranty Customer Service Tel